ADVrider

ADVrider (http://www.advrider.com/forums/index.php)
-   Parallel Universe (http://www.advrider.com/forums/forumdisplay.php?f=77)
-   -   F8GS Foot Brake Lever Top Position (http://www.advrider.com/forums/showthread.php?t=827804)

Steveman 09-20-2012 02:15 AM

F8GS Foot Brake Lever Top Position
 
Sorry if this questions has been already raised. I did a search but had results with zillion possibilities.... However, think its in the nature of a forum that some questions may have been asked several times. Pls dont shoot me :D

After a short ride I tried to adjust the foot brake lever as it is far too low for offroad riding when I stand on the pegs. Unfortunately the pedal seems to be already in its top position as the lever touches its upper stop (I think thats the stoplight switch).
Turning the spindle just reduces the pedals gap. Sure I can add a bracket on the pedal so that it gets higher but I'd like to have a possibility to lift and lower the lever as I am not always riding off road.

I think the position of the pedal is standard but I can remember that when I installed the TouraTech crash bars that I had to take of the brake pedal and had to add a small bracket or plate, cant remember for what this was but am sure that this did not change the pedals original position.

How did you solve the problem?

Regards
Steve

Loutre 09-20-2012 04:48 AM

I found that enlarging the Brake lever helps. Maybe try that if you can't lift the position

malloy 09-20-2012 07:02 AM

Grind down the tang on the back of the pedal arm where it makes contact with the brake light switch. Then adjust the connector to the rear master cylinder.

ebnelson 09-20-2012 08:03 AM

Putting Fastway pegs on "low boy" position has brought the relative height of the brake pedal up for me.

3Rrr 09-20-2012 01:36 PM

Bend it
 
Quote:

Originally Posted by Steveman (Post 19636733)
Sorry if this questions has been already raised. I did a search but had results with zillion possibilities.... However, think its in the nature of a forum that some questions may have been asked several times. Pls dont shoot me :D

After a short ride I tried to adjust the foot brake lever as it is far too low for offroad riding when I stand on the pegs. Unfortunately the pedal seems to be already in its top position as the lever touches its upper stop (I think thats the stoplight switch).
Turning the spindle just reduces the pedals gap. Sure I can add a bracket on the pedal so that it gets higher but I'd like to have a possibility to lift and lower the lever as I am not always riding off road.

I think the position of the pedal is standard but I can remember that when I installed the TouraTech crash bars that I had to take of the brake pedal and had to add a small bracket or plate, cant remember for what this was but am sure that this did not change the pedals original position.

How did you solve the problem?

Regards
Steve

I simple grabbed the foot brake lever by the end and bent it outwards (away from the bike) so that the top (vertical) triangle of the brake lever was easily reachable when standing. In it's stock position this part of the lever is too close to the bike to step on with the boot.

Works like a charm. Takes 10 seconds. And best yet - costs nothing.:clap

Steveman 09-20-2012 11:37 PM

guys, many thanks for all your hints. Yo, I did already think about grinding the pedals stop down a bit but as this is irreversible I finally didnt do it.

Quote:

Originally Posted by 3Rrr (Post 19640471)
I simple grabbed the foot brake lever by the end and bent it outwards (away from the bike) so that the top (vertical) triangle of the brake lever was easily reachable when standing. In it's stock position this part of the lever is too close to the bike to step on with the boot.

Works like a charm. Takes 10 seconds. And best yet - costs nothing.:clap

I will try this, now that I read that I can remember that I saw a video about off road riding techniques where the trainer did something similiar. With big pliers he bent the vertical triangle outwards. After that it wasnt exactly vertical anymore but could be reached with the boot. Maybe this triangle is intended for being used in the described way.

However, thanks for the hint, seems its a good idea and does not cost me anything :clap

BR, Steve

3Rrr 09-20-2012 11:47 PM

May I recommend the "no pliers" approach
 
Quote:

Originally Posted by Steveman (Post 19644596)
guys, many thanks for all your hints. Yo, I did already think about grinding the pedals stop down a bit but as this is irreversible I finally didnt do it.



I will try this, now that I read that I can remember that I saw a video about off road riding techniques where the trainer did something similiar. With big pliers he bent the vertical triangle outwards. After that it wasnt exactly vertical anymore but could be reached with the boot. Maybe this triangle is intended for being used in the described way.

However, thanks for the hint, seems its a good idea and does not cost me anything :clap

BR, Steve

It was on the BMW Off-road DVD by RawHyde. I found that using large pliers actually wanted to twist the brake pedal. Was easier to just pull the pedal outwards from the end of it. This left the vertical triangle perpendicular to the pedal.

Happy braking!

Kyle

nzcvlh 09-22-2012 06:08 AM

I cut the stop off of the lever and brazed on a coupling nut about 1 inch long and then added a threaded stainless steel bolt and jam nut. Now I have complete adjustability. Works and looks great, I like to change the position depending on boots and type of riding.

Dave

Bear Creek West 09-22-2012 07:38 AM

Quote:

Originally Posted by nzcvlh (Post 19653489)
I cut the stop off of the lever and brazed on a coupling nut about 1 inch long and then added a threaded stainless steel bolt and jam nut. Now I have complete adjustability. Works and looks great, I like to change the position depending on boots and type of riding.

Dave

any chance you can post a picture of this mod?

nzcvlh 09-23-2012 05:11 AM

sure, I'll take a pic and post today.

Steveman 10-13-2012 03:57 PM

Quote:

Originally Posted by nzcvlh (Post 19659149)
sure, I'll take a pic and post today.

I see :D


Times are GMT -7.   It's 10:26 AM.

Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014