ADVrider

ADVrider (http://www.advrider.com/forums/index.php)
-   Orange Crush (http://www.advrider.com/forums/forumdisplay.php?f=34)
-   -   Replacement brake rotors for 990 with ABS - options/where to buy (Australia) (http://www.advrider.com/forums/showthread.php?t=853051)

striped tomato 01-03-2013 08:24 PM

Replacement brake rotors for 990 with ABS - options/where to buy (Australia)
 
I've searched the forums and so far only established that most of the replacement brake rotors available do not suit the ABS version of the 990. Can anyone tell me which products do (Brand/Part Number) and where we can get them in Oz?

Cheers

Steve

Jim Colombotos 01-03-2013 08:47 PM

here ya go, not in oz but may help get you started

http://blackdogcw.com/black-dog-shop...19-detail.html

striped tomato 01-04-2013 03:46 PM

Quote:

Originally Posted by Jim Colombotos (Post 20390827)
here ya go, not in oz but may help get you started

http://blackdogcw.com/black-dog-shop...19-detail.html

Many thanks, when I looked up on my usual suppliers website the Galfer ones said not suitable for ABS - would probably prefer not to use factory ones again as they rattle a lot and make me a bit uncomfortable.

I read somewhere that EBC also do them but can't find a part number.

Steve

Alex_RO 01-04-2013 08:52 PM

Options
 
Hello,

I'm looking for some disks also.


There are some EBC codes mentioned in post 19 of this thread - http://advrider.com/forums/showthread.php?t=695229 .

Moto-master has a couple of options for ABS 990 (at least for the rear disc). I'm sure they have options for the front disks but i only inquired about the options for the rear disk.

"For KTM 990 adventure rear we have fixed rear discs in our range ( not floating like the original )

The 110312 is a Flame design model which has boltholes with a countersink for non-ABS models.
The 110403 is a Flame design with no countersink around the boltholes, for ABS models like yours.

Availble as from te beginning of february, our new "HALO" series of circular round discs;


The 110472 is a round design model which has boltholes with a countersink for non-ABS models.
The 110490 is a round design with no countersink around the boltholes, for ABS models like yours. "

Hope it helps.

KTMSER 01-05-2013 06:19 AM

http://advrider.com/forums/showthrea...ghlight=rotors




The EBC's are still holding up........:deal

Alex_RO 01-05-2013 06:21 AM

Quote:

Originally Posted by KTMSER (Post 20400821)
http://advrider.com/forums/showthrea...ghlight=rotors




The EBC's are still holding up........:deal


Question: are they "floating" type rotors? Just kinda wondering if that's ...mandatory.

rossguzzi 01-05-2013 04:59 PM

KTMSER, I have read all your post re EBC floater and tried to search them at Sumit Racing but no luck. Is that where you got yours?
Cheers

KTMSER 01-05-2013 07:33 PM

I had the local Honda dealer order them thru Parts Unlimited...

There are several UK dealers that list them with a quick Google search...

Here is one..

http://www.mandp.co.uk/productinfo/5...rake-Discs/EBC

USA dealer http://www.perfectbrakes.com/products.asp?cat=5296



MD6299D front

MD6298D rear


These fit all 990's as well as the 950's

rossguzzi 01-05-2013 09:46 PM

Thanks for that info :)

Cheers.

srad600 01-05-2013 10:31 PM

Quote:

Originally Posted by Jim Colombotos (Post 20390827)
here ya go, not in oz but may help get you started

http://blackdogcw.com/black-dog-shop...19-detail.html

Nice find Jim...I've been looking to replace my rotors for a little while. They're already warped...along with my tacoed front wheel the front end on my bike needs some love. :freaky

bikyto 01-07-2013 08:23 AM

The non abs 950/990 rotors work well on the abs version as well with a mod that takes 30 sec and costs 5 cents.

It goes like this:
Install the new rotors
Unscrew the abs sensor
Add washer behind the abs sensor
Screw the abs sensor bolt back on
Done

I'm running the galfer rotors. Works great.

Bannisdale 01-08-2013 04:44 AM

EBC Poor Quality
 
I recently fitted an EBC rear disc to my non ABS 950.

It rained....I put the bike away....it rusted....I'm talking sitting in the garage overnight!

Got a replacement under warranty. Was told the coating was faulty?

First ride out with new disc....it rained....it went rusty.

Sent it back for a full refund and bought a Brembo no more rust.

The original was 7 years old and looked better than the EBC after 7 hours.

I'm sure they're not all like this but I won't be buying EBC again.

Cheers

Tim

rossguzzi 01-08-2013 06:09 AM

Quote:

Originally Posted by Bannisdale (Post 20425569)
I recently fitted an EBC rear disc to my non ABS 950.

It rained....I put the bike away....it rusted....I'm talking sitting in the garage overnight!

Got a replacement under warranty. Was told the coating was faulty?

First ride out with new disc....it rained....it went rusty.

Sent it back for a full refund and bought a Brembo no more rust.

The original was 7 years old and looked better than the EBC after 7 hours.

I'm sure they're not all like this but I won't be buying EBC again.

Cheers

Tim

Was that a floating one?

Bannisdale 01-08-2013 10:59 AM

Quote:

Originally Posted by rossguzzi (Post 20426017)
Was that a floating one?

No, solid rotor. I would hope that the centre carrier on a floater would be coated in some way. I was shocked how quickly this rusted. like an old Guzzi disc!

rossguzzi 01-12-2013 07:17 AM

I tried to email 'Perfect Brakes' twice and they keep bouncing back. Anyone know if they are still in business?
Better still if anyone in the US could try to ring them to see if they stock the EBC MD6299D rotors and post here or PM me it would be great. Others may like this info too.

Perfect Brakes, Inc
USA
1 (888) 632-8068
1-216-581-8950

email: sales@perfectbrakes.com


Cheers


Times are GMT -7.   It's 04:46 AM.

Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014