ADVrider

ADVrider (http://www.advrider.com/forums/index.php)
-   Parallel Universe (http://www.advrider.com/forums/forumdisplay.php?f=77)
-   -   BMW topcase and Jesse rack? (http://www.advrider.com/forums/showthread.php?t=860784)

FredRydr 02-04-2013 11:34 AM

BMW topcase and Jesse rack?
 
Will the Jesse rack for Odyssey panniers preclude use of the F800GS Vario top case?

Fred

nytrashman 02-04-2013 11:53 AM

i have jesse boxes on my 650 twin and a givi top box. i had to use some shims to move the rack out approx 1/2" so the jesse boxes would open without hitting the top box. i am sure you will have to do the same thing when using the BMW top case.

you can see in this pic the unpainted shims on the left that move the jesse rack out enough to allow the boxes to open.

http://www.pbase.com/george_f/image/137128849.jpg

FredRydr 02-04-2013 12:12 PM

Thanks, but will the Jesse rack preclude re-installation of the mounting plate for the Vario top case?

Fred

GH41 02-05-2013 01:36 PM

Quote:

Originally Posted by FredRydr (Post 20648796)
Thanks, but will the Jesse rack preclude re-installation of the mounting plate for the Vario top case?

Fred

You will have to either cut the rear post on the Vario plate down or shim the front post up and buy 4 longer bolts. I chose to cut the rear post and use the supplied bolts. GH

FredRydr 02-16-2013 11:12 AM

Quote:

Originally Posted by GH41 (Post 20657183)
You will have to either cut the rear post on the Vario plate down or shim the front post up and buy 4 longer bolts. I chose to cut the rear post and use the supplied bolts. GH

Is that the steel part or the plastic part that you cut? I can buy the steel part from a fellow inmate.

Fred

GH41 02-17-2013 03:44 AM

The plastic Vario base plate has a steel core. You have to cut down the rear post by the height of the Jesse crossover piece. I'll put up a picture later. GH

FredRydr 02-25-2013 05:22 AM

Quote:

Originally Posted by GH41 (Post 20744012)
I'll put up a picture later. GH

Thanks, GH. That should help.

Fred

FredRydr 03-30-2013 12:07 PM

GH,

I pulled the steel plate under the topcase bracket. Which posts did you cut down, and by how much?

Fred

GH41 03-30-2013 03:43 PM

The rear post. Think about it... You have to remove the material that the Jesse cross piece now occupies. I am not able to check right now but I remember cutting the post almost down to the plate. If you cut too much or too little it's no big deal as long as you can start the bolts. GH

RheinGold 03-31-2013 06:30 PM

I have the Jesse bags and the Vario top case (on the OEM rack). You are correct they don't work together...adding the Jesse case racks places the BMW top case rack at an angle so you can't get all four bolts in.

However, Al Jesse has a simple solution...he sent me two spacers and longer bolts and it goes together perfectly, although the Vario case/rack does end up about 3/4" higher than it would otherwise be. But, it really makes no difference...works great.


Times are GMT -7.   It's 05:17 AM.

Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014