ADVrider

ADVrider (http://www.advrider.com/forums/index.php)
-   Orange Crush (http://www.advrider.com/forums/forumdisplay.php?f=34)
-   -   Splitting cases, HOW? (http://www.advrider.com/forums/showthread.php?t=927725)

Qwik 10-16-2013 05:13 PM

Splitting cases, HOW?
 
I have my old motor out and need to. Get the rest of it dismantled so I can send CJ the transmission that I owe him. I have the heads and cylinders pulled but can't get any farther than that. How do I get the gears off so I can pull the rest?

Sumi 10-16-2013 05:36 PM

Maybe this is stupid, but.. service manual?

VxZeroKnots 10-16-2013 05:48 PM

I've never seen the service manual but perhaps using a case splitter like on thumpers?

renogeorge 10-16-2013 08:52 PM

You are going to need pullers and an impact wrench before you can split the cases. As mentioned, if you are asking, you could benefit from the service manual.

Zuber 10-16-2013 11:11 PM

Well where do we start?

Oh, Yeah, first get a service manual.

Qwik 10-17-2013 11:13 AM

Quote:

Originally Posted by renogeorge (Post 22570535)
You are going to need pullers and an impact wrench before you can split the cases. As mentioned, if you are asking, you could benefit from the service manual.

Well I needed an excuse to buy an impact wrench anyway.

kamanya 10-17-2013 01:17 PM

+1 on a manual.

But, to get you going, the rotor/flywheel has to be pulled off to get to the balancer shafts. Nothing is coming apart till then.

The big arsed gear on the right side of the crank can stay to get the cases spit but has to come off if you want the crank out of the right hand case.

Clutch has to come off.

Katoom119 10-18-2013 10:24 AM

I've got the manual printed out. If you need it let me know and I'll send you pictures of the appropriate pages.

Just Paul 10-18-2013 12:50 PM

I have it on PDF Tim, let me know and I will hook you up.

Oldebonz 10-18-2013 03:21 PM

splitting cases
 
Haven't had need to split any of my KTM's but Pep Boys has a Kawasaki brand impact driver rechargeable that will get anything off,many times using your hand instead of special holder tools.A penny or nickel placed between primary and clutch gears will jam them without any harm to gears to get off crank nut,Motion Pro sells a great universal holder that will work with about any thing,looks like a vice grip.Universal gear pullers from Harbor Freight work well and are cheap enough to modify by grinding arms to fit .Don't forget your old friends heat and cold.Hot air guns will warm up aluminum without warpage or damage to the cases making separation easy.Main bearings may come out of cases still on crank or gear shafts but are easily removable with a Harbor Freight beveled bearing separator .When putting things back together,put your crankshaft in the freezer,warm up the ball or roller bearing mains with the heat gun and install with your fingers(gloved!) and no hammers or violence,put this assembly into the freezer,warm the cases to the point of being too hot to touch and push things together with your hands.Can't knock a newly aligned crank(roller bearing) out of line this way.New transmission bearings and seals,also fork seals can be pushed fully into place by freezing them and warming the aluminum case or fork.I have rebuilt many Yamaha,Bultaco,Husqvarna,Ossa etc.engines in this manner with no hammers,special tools,no forcing or hammering,everything spinning well an not leaking.Tighten up case bolts to specs,if any binding occurs,warm cases and give them a few smacks with a rawhide mallet(not on shafts) and everything will spin freely.Hope this will make someone's life a little easier and less expensive!:wink:


Times are GMT -7.   It's 05:57 AM.

Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014