ADVrider

Go Back   ADVrider > Search Forums
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Showing results 1 to 25 of 25
Search took 0.01 seconds.
Search: Posts Made By: cragdweller
Forum: Thumpers 03-22-2015, 02:43 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Aftermarket top clamp

I've been searching all over this thread and the web for more details and pictures of aftermarket top triple clamps for the XRR. What I can't clearly tell is which of these clamps offers the...
Forum: Thumpers 03-08-2015, 09:39 PM
Replies: 7
Views: 1,555
Posted By cragdweller
I used aluminum spacers with a stainless outer...

I used aluminum spacers with a stainless outer sleeve, I believe from Moose Racing. They still score a bit, but are much more resistant to wear than the aluminum stock spacers. Mine are holding up...
Forum: Thumpers 03-02-2015, 08:55 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
One of the three accelerator pump diaphragm cover...

One of the three accelerator pump diaphragm cover screws bumps up against the stock headpipe when you're trying to get the carb level. I just clearanced it a little bit to give me a bit more room. ...
Forum: Thumpers 03-02-2015, 05:44 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Told you you would like it!:norton[/QUOTE] ...

Told you you would like it!:norton[/QUOTE]

It makes better WFO power than the stocker, but the best part is the partial throttle transitions. Much easier to modulate small throttle openings with...
Forum: Thumpers 03-01-2015, 09:08 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Fcr-mx

Just finished the FCR-MX installation. Lots of little details to make it fit. NOSS Machine adapter. Removed the cable operated hot start plunger and replaced with pull-knob style. Did a bit of custom...
Forum: Thumpers 02-26-2015, 10:03 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Here is a link you should look at that shows the...

Here is a link you should look at that shows the correct part numbers for petcock reseal:

http://www.advrider.com/forums/showpost.php?p=21120925&postcount=16733
Forum: Thumpers 02-25-2015, 07:11 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Also check the rubber disc inside the petcock. ...

Also check the rubber disc inside the petcock. It comes apart too...
Forum: Thumpers 11-28-2014, 01:29 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Yeah that looks like good stuff...

Yeah that looks like good stuff...
Forum: Thumpers 11-27-2014, 05:26 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
I did the oil level sight tube mod to my bike,...

I did the oil level sight tube mod to my bike, but used 1/8" tubing instead of 1/4", with the reasoning that if the tubing got pinched, abraided, grabbed by a branch, etc., that it would be a smaller...
Forum: Thumpers 07-13-2014, 09:21 AM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
XRL is much cheaper to build, still selling...

XRL is much cheaper to build, still selling unchanged for 20+ years, so they are making more money on it than they would be continuing with the XRR.
Forum: Thumpers 06-27-2014, 07:03 AM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
They actually built it to compete with the...

They actually built it to compete with the then-dominant KX500s...
Forum: Thumpers 05-06-2014, 06:01 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
I just meant that the XRR gear ratios are closer...

I just meant that the XRR gear ratios are closer together than optimal for a do-it-all bike. It would be nice to have a lower first or a taller fifth, with the other ratios nicely spaced in between....
Forum: Thumpers 05-05-2014, 08:53 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Any further word on this? I'm very hopeful for...

Any further word on this? I'm very hopeful for your experiment. The XRR trans gear spacing is really the only flaw...
Forum: Thumpers 03-06-2014, 09:05 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
This is not needed. If you drill carefully and...

This is not needed. If you drill carefully and use a shop vac during the process, you'll be fine. As others have mentioned, grease the tap and clean the tap grooves frequently. No worries. I did...
Forum: Thumpers 03-05-2014, 08:42 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Hose the pads down with brake cleaner and...

Hose the pads down with brake cleaner and install. You'll be fine.
Forum: Thumpers 01-31-2014, 06:48 AM
Replies: 4,897
Views: 1,285,963
Posted By cragdweller
Thanks! Mmmmmmm Hmmmmmm

Thanks! Mmmmmmm Hmmmmmm
Forum: Thumpers 01-30-2014, 07:30 AM
Replies: 4,897
Views: 1,285,963
Posted By cragdweller
Can anyone tell me the overall height of a stock...

Can anyone tell me the overall height of a stock TW200 (without the mirrors)? Wondering if I pull the mirrors off if the bike will fit in the bed of my full size pickup with a canopy. If someone...
Forum: Thumpers 01-25-2014, 08:10 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
I acquired a super clean 2000 XRR that had been...

I acquired a super clean 2000 XRR that had been titled as a street legal bike soon after it was initially purchased in Southern Oregon. Plates had never been issued from OR DMV, but the VIN was in...
Forum: Thumpers 05-16-2013, 06:42 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Detonation causes cracked pistons. Overheating...

Detonation causes cracked pistons. Overheating can contribute to this, but I would look at fueling (both mixture and grade) and timing first. That piston died from detonation.
Forum: Thumpers 05-04-2013, 10:01 AM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
My 2000 has its rearend pushed to the left when...

My 2000 has its rearend pushed to the left when viewing from behind. I know this is a common thing on these bikes. I'm not sure if mine was that way when it was new, at least not to the degree it...
Forum: Thumpers 04-07-2013, 10:45 AM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Very useful Jayrod! Thanks!

Very useful Jayrod! Thanks!
Forum: Thumpers 12-04-2012, 07:53 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Any new info on the wide ratio gearset?

Any new info on the wide ratio gearset?
Forum: Thumpers 11-20-2012, 06:31 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
More info on the wide ratio trans gears, please! ...

More info on the wide ratio trans gears, please! I'm in!
Forum: Thumpers 08-29-2012, 07:29 PM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
Best bearing kits

Just looking for feedback on the quality of the various linkage/swingarm/wheel bearing kits out there. I have seen All Balls, Moose, Pivot Works, and of course Honda OEM. I've searched and not...
Forum: Thumpers 08-17-2012, 09:44 AM
Replies: 23,500
Views: 3,111,450
Posted By cragdweller
big guy springs

Have any of you big guys (I'm 6'4", 240) resprung the stock XRR forks/shock without revalving? I'm about to do this just to see how the stock valving works for my type of riding. Just curious how...
Showing results 1 to 25 of 25

 
Forum Jump

Times are GMT -7.   It's 10:24 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2015