ADVrider

Go Back   ADVrider > Search Forums
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: Fingers
Forum: Thumpers 06-29-2014, 08:36 AM
Replies: 22,166
Views: 2,680,691
Posted By Fingers
Edelbrock Pump Assembly on ebay

Bagged this today, maybe they are being made again.....
I'll bet there are a lot of Harley drivers looking for parts as that was the carbs original application....

...
Forum: Thumpers 06-23-2014, 02:25 PM
Replies: 22,166
Views: 2,680,691
Posted By Fingers
OK sure enough Jegs canceled my order, all 4...

OK sure enough Jegs canceled my order, all 4 parts unavailable. I will try to Skype to Edelbrock with fingers crossed tomorrow.
FWB, the "ball bearing" is called the pump check ball it and little...
Forum: Thumpers 06-23-2014, 10:02 AM
Replies: 22,166
Views: 2,680,691
Posted By Fingers
Edelbrock Parts

I placed an order at Jegs for the following parts on friday:
351-9097/9096/8640 and 8326, they are, in order, the Pump Assembly (complete)/pump check needle and bearing (that always goes...
Forum: Thumpers 06-07-2014, 07:56 AM
Replies: 75,424
Views: 7,966,310
Posted By Fingers
Intake Boot Clamp

Does anybody know where I can get a better (as in higher quality maybe stainless) clamp for the Intake boot to carb fitting (on the air filter side), one that will fit right? I have to remove often...
Forum: Thumpers 11-28-2013, 11:24 AM
Replies: 22,166
Views: 2,680,691
Posted By Fingers
When I switched to the Edy my mpg went way up,...

When I switched to the Edy my mpg went way up, but I think it had more to do with the stock carbs habit of pissing fuel out the overflows when leaned. Its hard to notice this as the fuel will hit the...
Forum: Thumpers 07-20-2013, 07:20 AM
Replies: 75,424
Views: 7,966,310
Posted By Fingers
Mike, Thanks, yes it is an OEM carb. I did not...

Mike,
Thanks, yes it is an OEM carb. I did not know there was a difference between OEM and Non OEM FCR MX carbs.
Good info for those following this thread as there are several that are building...
Forum: Thumpers 07-20-2013, 04:06 AM
Replies: 75,424
Views: 7,966,310
Posted By Fingers
Agree Nic, please post their response, I searched...

Agree Nic, please post their response, I searched a lot and I'm surprised I can't find anything about how it goes in!?! Since the threads are a good 15 mm from the needle seat it looks like they want...
Forum: Thumpers 07-19-2013, 10:54 PM
Replies: 75,424
Views: 7,966,310
Posted By Fingers
Adj Air Screw will NOT fit FCR MX

I tried to install the Adjustable Air Screw kit I got from Power barn into my FCR MX and it will not fit, not even close. The threads are about 2.5 mm wider than the fixed screw, so I suspect this...
Forum: Thumpers 07-14-2013, 05:55 AM
Replies: 75,424
Views: 7,966,310
Posted By Fingers
I got the Adj air screw 2 weeks ago from Power...

I got the Adj air screw 2 weeks ago from Power Barn. $12.95 shipped.
Forum: Thumpers 07-10-2013, 12:58 AM
Replies: 22,166
Views: 2,680,691
Posted By Fingers
I cross checked the part numbers for the shifter...

I cross checked the part numbers for the shifter pawl on the Honda microfich, and the part number for the stock pawl was the same across the 650 L, R as well as the XR/L 600.
Forum: Thumpers 07-09-2013, 11:20 PM
Replies: 22,166
Views: 2,680,691
Posted By Fingers
Roller shift pawl mod ( new Farkle)

Anyone know about this part?

http://www.factorypro.com/prod_pages/prodh_xr500,xr600,xr650,nx650,gb500.html

Apparently it's the same for all XR 650 motors. I bought one last week and hope to...
Forum: Thumpers 12-18-2006, 03:06 AM
Replies: 4
Views: 741
Posted By Fingers
More info would help, like what carb was the...

More info would help, like what carb was the replacement...however assuming by law of averages it was an edelbrock, that knurled knob is the idle adjustment screw (normal linked via a short cable....
Forum: Equipment 03-01-2006, 04:57 PM
Replies: 36
Views: 4,305
Posted By Fingers
Leatherman Crunch

Leatherman Crunch http://www.leatherman.com/products/tools/crunch/default.asp, it has a locking pliers and is small. The locking pliers is invaluable as a emer tool.
Showing results 1 to 13 of 13

 
Forum Jump

Times are GMT -7.   It's 01:20 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014