ADVrider

Go Back   ADVrider > Search Forums
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Showing results 1 to 9 of 9
Search took 0.01 seconds.
Search: Posts Made By: BrownMike
Forum: West California, the desert southwest and whatever is left 09-13-2011, 11:54 PM
Replies: 118
Views: 8,367
Posted By BrownMike
Not on here too much.. but figured I'd chime in ...

Not on here too much.. but figured I'd chime in
89 XT350
Scripps Poway area
Forum: Thumpers 09-01-2011, 04:40 PM
Replies: 4,360
Views: 597,599
Posted By BrownMike
Cut out the top of the airbox, and synced the...

Cut out the top of the airbox, and synced the carbs to open same time, definitely starts better, idles smooth down to about 1600ish. runs great when cold, but will start to bog off idle-2k once warm....
Forum: Thumpers 08-21-2011, 07:02 PM
Replies: 4,360
Views: 597,599
Posted By BrownMike
The airbox should still be stock (cant loo at the...

The airbox should still be stock (cant loo at the moment) and stock exhaust without the end cap as well. I drilled out the pilot to a #77 bit and it helped alot from where it was, but a real jet...
Forum: Thumpers 08-18-2011, 07:02 PM
Replies: 4,360
Views: 597,599
Posted By BrownMike
Ok so my bike has been running pretty decent...

Ok so my bike has been running pretty decent since I did all the carb work, but a couple issues have surfaced.

1. high rpm surge: at cruising speed ~60 mph it tends to bog hard and randomly surge,...
Forum: Thumpers 06-20-2011, 04:48 PM
Replies: 4,360
Views: 597,599
Posted By BrownMike
Krylon Plastic spraypaint...its MAGIC haha....

Krylon Plastic spraypaint...its MAGIC haha. Seriously takes old gross stained plastics to brand new in one coat, semi sheen finish.
Forum: Thumpers 05-27-2011, 08:18 AM
Replies: 4,360
Views: 597,599
Posted By BrownMike
Nope, why?? lol EDIT: Drilled the pilot out...

Nope, why?? lol

EDIT: Drilled the pilot out with a #77 drill bit, and it idles like a dream, and idles smoothly at 1500 rpm as well. No more end cap, pulls well through out. Problem solved!
Forum: Thumpers 05-26-2011, 05:38 PM
Replies: 4,360
Views: 597,599
Posted By BrownMike
Ok so I replaced the main with 130 today, shimmed...

Ok so I replaced the main with 130 today, shimmed the needle with one washer, and have it dialed out 3.5 turns and still has a consistently inconsistent miss at idle. Tried putting tape over the...
Forum: Thumpers 05-26-2011, 08:17 AM
Replies: 4,360
Views: 597,599
Posted By BrownMike
Already tried adjusting it, so far it runs best...

Already tried adjusting it, so far it runs best at about 3-3 1/2 turns out but still misses. I have made sure to blow out each passage with carb clean and compressed air each time Ive cleaned the...
Forum: Thumpers 05-24-2011, 04:37 PM
Replies: 4,360
Views: 597,599
Posted By BrownMike
too much reading...

HI! Ive been lurking on this thread for a few weeks after I got a 89 XT350 off a buddy of mine, and have been scouring this thread for info.

I have a few problems with the bike that I need to...
Showing results 1 to 9 of 9

 
Forum Jump

Times are GMT -7.   It's 01:29 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014