Items still needing identified or resolved:
- is there an aftermarket alternative?*'81 XR250R? not proven
a flexible cutting board from Walmart has been successfully used in a pinch to protect swingarm, using RTV silicone gasket to affix the flexible cutting board(shaped like OEM slider) to swingarm.
cross-reference -what other model will fit?
t: See Post #12, right above this post your are reading~thx Jeff@QuadShop
-- what other HOndas fit?
If you can answer
the above questions, please reply in the thread with your findings,
and/or send me a PM
so i can update and add it here, thanks!
If you have any question you want added, please pm and it will be
FAQs for the Honda NX250 AX-1 250 Dominator
I need a longer clutch cable for high bar risers, wider handlebars, longer fork tubes, or taller handlebars?
1984 Kawasaki GT550 (550GT)Kawasaki OEM#:
54011-1164 ~thank you Scrambler66+ArthDuro
Can I use a different CDI than the factory Honda part?
link CurtW found aftermarket CDI on Ebay link
Are there any other footpegs that will fit my stock NX peg carrier?
CRF50/XR50 pegs work without modifications~ArthDuro
The headlight won't work, but the other lights are fine, and all the fuses are fine....etc... why? What is wrong with my headlight?
There is a small spring in the 'start' button for the engine, built into the right hand control. This spring will get dirty, or become loose and break the circuit for the headlamp illumination.
carefully, disassemble the right hand control, and clean the contacts and the spring.
My NX250 keeps falling over, to the right side of the bike? wth?
Is there a K&N style air filter option for the NX250?
The OEM filter measures just under 4"x6" inches(add mm here VC!)
K&N makes Part #MG-0001
for the MotoGuzzi V1000 Lemans/California models.
It measures:Height: 1.22 in (31 mm)Outside Length: 5.984 in (152 mm)Outside Width: 4.449 in (113 mm)
. Some work is required, mainly cutting and filing. Then an adhesive is used to glue the OEM rubber frame to the K&N filter's body.
33-2263 is close, and is being experimented with.
What size tire or tube should i get for my 19" front rim, or 16"/17" rear rim?
here's a nice tube size chart
, and a nice tire conversion chart
What's my battery?
(same as Honda Rebel, Ninja 250) Ebay is a good source for inexpensive ones...
or here or here
For suggested starting prices, browse from there...
Also, look for the newer Gel type
batteries(add notes here VC
Another option is to find a battery with the same physical size, but more 'plates' are in the battery.
(Put example here VC!)
My NX250 fell over to the right, i need a front brake lever? Anything cheaper than stock?
Parts Unlimited has # 44-1001
Polished brake lever Honda for $5.95, also in black
My bike needs fork boots! Who makes some?
Daystar Fork boots Part# F00234
There are others, the boots need to fit 37mm forks, with x
amount of travel.
Why won't my bike spark?
Why doesn't it crank, or even hit a lick? Sometimes my bike misses, runs like crap and cuts off, then it won't start. My tachometer reads funny sometimes, or the tachometer doesn't move when the bike will turn over, but not start.
Check your CDI. If it starts with KW3
....its the old 80s CDI
there was a factory issue with the CDI in the late 80s.
They will all fail sometime. Replace with a known good cdi, before you look for other component failures.
is the new part, updated sequence code....
should be printed on the CDI plug area..
There is a good video of a functional CDI p#22.
Video of good CDI tach view here
CDI discussion on abouts page #22 of this thread.
My bike is hard to start when it's cold?( I use choke a mighty long time, or else the engine shuts off when it's cold. Also, it doesn't quite have the normal power i remember)
It needs intake valves adjusted (do all 4, shim under buckets)
for the short list of symptoms.
the carb's dirty
Is there a carb rebuild kit?
is the kit number.
Try Googling the part number, "NX250 Carb rebuild kit", or looking on Ebay.
is just a suggestion/illustration...it's pricey! on that site.
What parts fit my bike?
The NX250 doesn't 'share' parts with very many US machines. Internationally, the NX250, AX1, XL250 Degree use the same engine, share frames(though some are square rails, and some are round frame rails)
is a list of nearly all parts for the NX 250....Thx R
My shifter is 'loose'. Can i get an aftermarket shifter? What model should i use to crossreference?
The (84-85) XR200R, XR250R, (84-87)XL250R has the exact same shifter as the NX250.
The (84-99) XL600R, and XR600R will also fit!, thanks Jeff!theQuadShop.
A little bird told us the Yamaha TTR250 (99-06) will fit, but lengthwise?-VC
Can I get those funny rubber 'wellnuts', they are like threaded rubber sleeves that hold my cowls to each other and to the bike?
What is a good tire for my bike?
Did you read this page?
the one you are looking at to see these words? Tire discussion is on this page and the next few after this one.
Also around post #850, it's revisited a bit.
Where can i get the 17" rear wheel for swapping onto the NX250?
84-87 XL250R, 85-86 XL350R
Where can i get a cheap jack for my NX250? Something just to grease the chain, or check swingarm bearings and the like...maybe like a light duty lift/jack?
Where can i find the cheapest parts OEM online?
Promo materials section
If you have a scanned sales brochure, owners manual, or historical "flashback" information relating to the NX250, send it to me...and I'll post it in this message.
click to enlarge
An original sales receipt from your dealer would be smash out bangin'!!
~smell of mousehide~
Other bikes that were made at the same time as the NX250/AX1 include:
Pacific Coast(PC800), Gold Wing, Transalp, CB-1, Hawk GT, GB500, NX650, CBR, VTR, NX250, NX125, XR600R, XR250R CR500R, CR250R, CR125R, CR80R
Show us the above showroom
! OLD PIC that has all the above HONDA's..That would RULE!
This bike was available as the NX250, the Ax-1, Baby dominator, 250 dominator and the like..some with minor differences.including OEM 239cc equipped
Also offered as XL250 Degree, but not in the US.