Airhead Flea Market Thread (closed and archived)

If you still can't find one by summer, keep in mind the national BMW MOA rally will be bringing a lot of riders and bikes near you in July.

http://www.bmwmoa.org/rally13

If it's pretty enough, low miles, and what you want, I don't think 5K is too much for an R100GS. But I'm not an expert on these. Then of course there is how much money you have not how much it costs?

Good Luck.

Dustbox wrote, "I am in the pnw area and Im looking to buy a r100gs with low miles asap." Another place to look: http://marketplace.ibmwr.org/ads/rabs

I need a lower tree for a /5 it can be a bit rough I don't mind..

I have a bunch of /5 part to trade for it if you need something...

found

have a bmw factory exhaust wrench for sale.







75 shipped in the USA

Dam just bought one

Sent from my DROID RAZR HD using Tapatalk 2

PM sent.

$3800 in San Diego, Ca


New front brake pads, brake cable,rebuilt brake caliper and master cylinder with stainless steel line.
New plug wires. points replaced with after market dyna 3 electronic ignition.
Carbs rebuilt, rejetted and synced
New steering tube bearings.
Recent valve adjustment
Custom made seat, sub frame and custom made exhaust (sounds fantastic w/o being TOO loud).
New rear tire, front in good shape.
Rebuilt forks with new bushings, seals and fluid.
I have the rear main seal (just barely leaking) I am planning on installing and will lube the splines wile im in there.
Starts runs and drives perfect.
Very reliable
Clean current title in my name. Have too many bikes and I need money for other projects otherwise i would keep it.

Instruments? I can't see 'em?

There are also no fenders, either front or rear. No front fender holder/fork brace. No fork gators. Looks like no center stand, not sure. Carb enrichner looks like it might be part way on, either out of adjustment or the mentioned carb rejetting didn't come out as good as imagined.

May be just what somebody wants or it will be a slow sale because custom bikes are slow movers. An original bike usually sells faster.

What the? Someone stole my fenders while I wasn't looking!!! Ha, no, I have them and the instruments which I removed 1.5 years ago when the speedo broke with 28k on the odometer. I just couldn't decide what route to go for gauges so have been running without for now. The side stand is on there and clearly visible.

You did get me to run out to the garage and double check the enrichener lever, but it goes all the way level. Not sure why it was like that in the pic. I have several jets and tried many combinations, it runs quite well thank you for your concern though. I cant recall what jets I went with, but I think it was .05 larger all around and one click up on the needle.

-Boogers

Anyone need an original, black R100GS dual seat.
Excellent shape with no tears or rips.
Might fit an R100R, too, dunno.

$125.oo and shipping. Pics to come soon.

Sold.

Pair of Marzocchi shocks in working condition. Still hold air, don't think they leak, at least all last summer when I ran these, no leaks. 13 3/8 inch eye to eye. Probably from a Duck from the 80's, but worked on my airhead BMW.

100.00 plus shipping.

Pics: http://razzi.me/a/22552

As in the title... I'm really really in need of a R80 ST 32:10 final drive for my moorespeed project.....please help!

Looking for a working airhead engine for another project.... does anybody have one that they wouldn't mind getting rid of?

Rabid Transet fairing with lowers and mount for /6 or /7 airhead and 2 windshields (High and standard, standard shown).
Make offer


Bike not inclued!!
Joe

http://www.advrider.com/forums/showthread.php?p=20856978#post20856978 thanks for checking them out

Hein Gericke tank. I think it's 9-11 gal and was on my /7. Has cap but no petcocks (uses BMW airhead type)

Best offer.

Joe

I have a brand new seat cover for a LWB /5 that I can not use, yours for $50