ADVrider

Go Back   ADVrider > Bikes > Thumpers
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 11-15-2006, 05:58 AM   #1
mike cramb OP
Beastly Adventurer
 
mike cramb's Avatar
 
Joined: Mar 2006
Location: Perth
Oddometer: 1,312
BLEEDING THE FRONT BRAKES 640 adv

OK I just fitted the KTM hard part new high front guard and now want to bleed my brakes I am having problems and there is nothing on the index.

I am about to try and use a syringe to fill the lines cause nothin else is workin.

MIKE
__________________
we are already here!
mike cramb is offline   Reply With Quote
Old 11-15-2006, 06:19 AM   #2
snaggleXR650
Gnarly Adventurer
 
Joined: Jan 2006
Oddometer: 244
I'm FAR from an expert but...

I just use a small clear hose that fits tightly on the bleed nipple, 1/4"? or so available at Lowe's, Home Depot etc... Loop it over and secure both ends with a zip ty where they cross. As the loop is higher than both ends of the hose, and the bleed nipple, air can't get back in because air is less dense than the fluid and get's trapped in the loop. Crack the bleed valve and open the master cylinder. Pump the lever and KEEP THE MASTER CYLINDER FULL of fluid as the level will go down as you pump. Watch the hose and the air bubbles coming out. When you don't see anymore bubbles tighten the bleed valve, remove the hose and button up your master cylinder.

Wrong bike, but same principle, see page 9 here;

http://www.bajadesigns.com/2005%20We...%20Classic.pdf
snaggleXR650 is offline   Reply With Quote
Old 11-15-2006, 07:09 AM   #3
mike cramb OP
Beastly Adventurer
 
mike cramb's Avatar
 
Joined: Mar 2006
Location: Perth
Oddometer: 1,312
Quote:
Originally Posted by snaggleXR650
I'm FAR from an expert but...

I just use a small clear hose that fits tightly on the bleed nipple, 1/4"? or so available at Lowe's, Home Depot etc... Loop it over and secure both ends with a zip ty where they cross. As the loop is higher than both ends of the hose, and the bleed nipple, air can't get back in because air is less dense than the fluid and get's trapped in the loop. Crack the bleed valve and open the master cylinder. Pump the lever and KEEP THE MASTER CYLINDER FULL of fluid as the level will go down as you pump. Watch the hose and the air bubbles coming out. When you don't see anymore bubbles tighten the bleed valve, remove the hose and button up your master cylinder.

Wrong bike, but same principle, see page 9 here;

http://www.bajadesigns.com/2005%20We...%20Classic.pdf
Already done that tube etc but the brake fluids not movin stayin full even though im pumpin away.

Its given me the sh#$%$% and every time i spill abit got to wash it off or loose the pretty paint.
__________________
we are already here!
mike cramb is offline   Reply With Quote
Old 11-15-2006, 07:28 AM   #4
Muzungu
Adventurer
 
Muzungu's Avatar
 
Joined: Sep 2004
Location: East Africa but now Oregon
Oddometer: 52
It seems to me that your master cyl. has an air bubble that you can't get moving.
Try back bleeding.
I used to use a small oil can/pump with the clear tubing. Filll the can/pump with 5.1 and pump the master cyl. full through the slave cyl. bleeder.
Go very slowly and at times stop pumping the oil can/pump and "tickle" the master cyl. lever, you will see tiny air bubbles coming up past the clear plastic guard inside the master cylinder.
Also make sure your handle bars are turned so that the master cyl. is at the highest position possible, usually turned fully to the left.
Just go slow and don't get in a rush, it'll bleed.

Hope this helps
Muzungu is offline   Reply With Quote
Old 11-15-2006, 10:19 AM   #5
meat popsicle
Ignostic
 
meat popsicle's Avatar
 
Joined: Feb 2004
Location: Circumlocution Office of Little Dorrit
Oddometer: 14,137


I have never had this problem. The only bit I can offer is to SLOWLY and EASILY squeeze the lever (rapid pumping will create small bubbles that are very difficult to bleed out!) to get the big bubbles to float up in the reservior or down thru the bleed screws. I have the one-way valves on my bleed screws (Dual Star parts) so it's a tad different in how I perform that bit. Sorry I don't have a full method for ya.
__________________
Kronreif Trunkenpolz Mattighofen LC4 640

Its not so much staying alive; its staying human that counts.
meat popsicle is offline   Reply With Quote
Old 11-15-2006, 11:08 AM   #6
G.Kennedy
...
 
G.Kennedy's Avatar
 
Joined: Oct 2002
Location: LA, CA
Oddometer: 1,850
I back bleed and tickle the lever.

Go to the local pharmacy and get two big syringes, and then the hardware for clear tubing. Fill one with fluid and connect to nipple via tubing. Open nipple and slowly push the fluid up the pathway. Have a buddy tickling the lever and removing fluid with the other syringe, as the level rises.

Have the bike on the side stand, with the handlebars turned to the left.

EDIT: Have your buddy occasionally push down the high loop of brake tubing ... make sure the MC is the high point.


Should work.
__________________
'00 R1100RT
'05 525EXC
'08 Hypermotard
IBA#11791
G.Kennedy is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 09:41 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014