ADVrider

Go Back   ADVrider > Bikes > Orange Crush
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 03-17-2011, 11:45 PM   #1
Tirespin OP
Gnarly Adventurer
 
Tirespin's Avatar
 
Joined: Jul 2003
Location: Where the Muk is Heckilteo?
Oddometer: 233
Weld86 kickstand bracket mod & install

I ordered the skidplate and kickstand bracket from Weld86. I'm happy with both.

The kickstand bracket I'm also pleased with, but after looking it over and the mounting bosses on the engine, I decided I would rather it not bolt to the engine case bosses at all. I chamfered the backside of the bracket so that a M10x30mm flat head bolt sat flush with the surface, bolted the kickstand to the bracket with nylock nuts, then bolted the entire assembly to the frame and the front engine bolt (with goes into a much thicker and stronger looking part of the engine case). I think this is how the BDCW bracket attaches, but this setup adds the front bolt as well. With this mod, I think I have the best kickstand bracket you can get!

Kudos to Weld86 for two good products at great prices.









The skidplate is a quality piece, thick aluminum, nice welds, and a perfect fit. There is no issue with it and the new style of SWMoto tank guards. It is quite heavy and full coverage; check out how high it comes to the exhaust pipe on the right side. I think it could be lighter without giving up any real protection just by having it not come up so high on the sides. Overall I'm happy with it, I'm good erring on the side of too strong. I may still cut it down a bit, and I'll add a cable from it to the rear brake lever.

__________________
Skip 2010 KTM 990 Adventure R Fuel and Maint Log
Tirespin is offline   Reply With Quote
Old 03-18-2011, 08:11 PM   #2
dpforth
no inline fours
 
dpforth's Avatar
 
Joined: Oct 2010
Location: Fantasy, I mean Vancouver Island
Oddometer: 289
I had the same idea...

Countersunk screws that is. Then I reconsidered as I thought it could (in an incident) put too much stress on the front bolt into the cases.

Still academic at this point as mine hasn't arrived yet.

Sure wish Weld86'd do a skid plate for the SE Some one close want to lend him their bike for a while?
dpforth is offline   Reply With Quote
Old 11-25-2011, 08:53 AM   #3
MortimerSickle
Semi-Adventurer
 
MortimerSickle's Avatar
 
Joined: Dec 2005
Location: Rainville, Orygun, where moss is a road hazard.
Oddometer: 11,675
Follow up?

Have you found any problems with the bolt mod?
__________________


I miss round headlights.

"When I was a young man, I liked to race my horse...." -
G.H.W.S. 1878-1962
MortimerSickle is offline   Reply With Quote
Old 11-25-2011, 11:15 AM   #4
Zander
Gnarly Adventurer
 
Zander's Avatar
 
Joined: Mar 2008
Location: Montreal
Oddometer: 194
Quote:
Originally Posted by MortimerSickle View Post
Follow up?

Have you found any problems with the bolt mod?
I have to install my Weld86 bracket and I like your mod.

I see that both countersinks reach the edge of the aluminum plate. I was wondering if cracks would develop on these narrow areas caused by the pressure applied by the side stand.

Usually, the edge distance (from center of hole to the edge of part) should be around twice the size of the fastener shank.

Let us know how it turned out.
__________________
Beginner's mind !
KTM 950

Zander screwed with this post 11-25-2011 at 12:07 PM
Zander is offline   Reply With Quote
Old 11-25-2011, 01:46 PM   #5
mcmann
Motorcycle Maniac
 
mcmann's Avatar
 
Joined: Nov 2006
Location: Jefferson, GA
Oddometer: 1,445
I counter-sunk the bottom bolt (which is where it usually cracks) and bolted the upper bolt into the case with a washer between the bracket and case (I mount the bike with the reinforced side stand down) due to short legs . . . . and need the additional support.

__________________
Young at heart . . . Never met a bike I didn't like
Motorcycles: my Happy medicine

2011 DL650 V-Strom "Real World"
2014 FZ-09 for the "WOW World"
mcmann is offline   Reply With Quote
Old 12-08-2011, 10:51 AM   #6
Tirespin OP
Gnarly Adventurer
 
Tirespin's Avatar
 
Joined: Jul 2003
Location: Where the Muk is Heckilteo?
Oddometer: 233
I've had no issues. I sometimes mount/dismount by standing on the pegs with the bike on the stand, with no signs of stress or damage. I don't have any concerns about it, since it's now physically impossible to crack the case with the stand, and if anything at all is damaged it's just the bracket.

The chamfer is not as deep as it looks in the picture. I didn't leave 1/2 the material, but there is a noticeable vertical portion of the hole left. I just went deep enough to make the bolt heads flush, which is required for this mod to fit. Also, since I just used a handheld die grinder, I intentionally went deeper in the center than I needed to, in order to get the contact area out where the hole was wider. If you have the right tool to make the chamfer, it would be better.
__________________
Skip 2010 KTM 990 Adventure R Fuel and Maint Log
Tirespin is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 09:47 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014