DR350/250 Picture/Mod Thread! - Page 42

MrPulldown · 01-03-2012, 02:36 PM

How does it work with the exhaust. Is there an extra support. Is it made out of burn resistant material. Seems really close to the pipe, and jsut lays on the plastic. Esspecially if it was packed full, or worse laid down on that side.

Lasherman · 01-04-2012, 11:49 AM

Quote:

Originally Posted by MrPulldown

How does it work with the exhaust. Is there an extra support. Is it made out of burn resistant material. Seems really close to the pipe, and jsut lays on the plastic. Esspecially if it was packed full, or worse laid down on that side.

Well, I only took it on a short ride but there is enough room between the exhaust. Im not worried about the heat issue. The bags lay on the side panels and strap down tight. It seems a lot better than a bag spider netted down. I have two tubes, all tools to change tires, pump, and misc. Stuff with room left over.

Skopelos · 01-12-2012, 02:25 AM

Hey guys here is a tour I have made with my beloved DR 250S, have a look

http://advrider.com/forums/showthread.php?t=754924

Lasherman · 02-05-2012, 07:37 PM

More fun than watching the firs half of the Superbowel.

ooooh Lookie! Some mud!

Who needs a kickstand when you have a rut with mud?

Need I say more?

woolsac · 04-13-2012, 08:48 AM

Quote:

Originally Posted by Lasherman

I converted all the blinkers and brake light to LED. I was breakingb bulbs while riding hard and LED's wont shatter from the impacts. Added a new front fender and new rear fender, a got the GPS on the handel bars, and a shark-fin for the rear break, rear rack and grab bar.. Also replaced a lot of maintence stuff like chain and doodads....

It's coming along....

What are those blinkers? I like the low profile/rear fender install of them...

Lasherman · 04-17-2012, 08:00 PM

Quote:

Originally Posted by woolsac

What are those blinkers? I like the low profile/rear fender install of them...

Got them off Ebay.....just typed LED motorcycle blinkers......

Lasherman · 04-17-2012, 08:11 PM

These were taken during Warped Vlll

Getting ready to ride in the rain and snow.

Got better later on..

This is on the Rencon Trail

Cannell Trail

dankatz · 06-02-2012, 11:38 AM

Trying to get my wife to ride. She did the MSF course and have ridden maybe a total of 5 times after it. We sold the ninja 250 and got a Monster 696 a couple of years ago, but she is too afraid. Was thinking of lowering the 1995 DR350SE so she could use it. I am 5'8" and she is 5'5 or 5'6" with a long inseam, so am thinking of the Kouba 1.5" lower link (#1) so I could still ride it comfortably. Does anyone have any pictures of a lowered bike? How much does it affect handling or off road prowess? Should I invest in Corbin instead?
Thanks!
Dani

plugeye · 06-03-2012, 08:30 AM

dr350sex

FlyingWman · 09-13-2012, 06:37 PM

1999X

Jeff@TheQuadShop · 10-01-2012, 10:04 AM

Who is this Jesse that lots of people refer to?

z@ch · 10-01-2012, 10:07 AM

Jesse Kientz, DR guru

http://www.kientech.com/

Lasherman · 11-04-2012, 06:55 PM

jaredyates · 11-05-2012, 04:00 PM

I've recently sold my DR250, but one of the leftovers that I have is a 31mm pumper carb off of a dirt DR250. Is anyone looking for one? I got it from an ebay seller and never tried to install it, so I'm not sure how well it works or what it takes to get it onto a street bike. Folks say that these can wear out, but I don't really know how to measure this one to see if it has worn out or not. I have precision measuring tools and can put them to use with guidance of what to measure.

tntmo · 11-05-2012, 06:30 PM

Quote:

Originally Posted by jaredyates

I've recently sold my DR250, but one of the leftovers that I have is a 31mm pumper carb off of a dirt DR250. Is anyone looking for one? I got it from an ebay seller and never tried to install it, so I'm not sure how well it works or what it takes to get it onto a street bike. Folks say that these can wear out, but I don't really know how to measure this one to see if it has worn out or not. I have precision measuring tools and can put them to use with guidance of what to measure.

I may be interested as an install on my DRZ250. PM inbound.

01-03-2012, 02:36 PM	#616
MrPulldown Beastly Adventurer Joined: Aug 2009 Location: Truckee Oddometer: 1,270	How does it work with the exhaust. Is there an extra support. Is it made out of burn resistant material. Seems really close to the pipe, and jsut lays on the plastic. Esspecially if it was packed full, or worse laid down on that side. __________________ 94 DR 350 SE

01-12-2012, 02:25 AM	#618
Skopelos Adventurer Joined: Nov 2011 Location: Athens, Greece Oddometer: 26	Hey guys here is a tour I have made with my beloved DR 250S, have a look http://advrider.com/forums/showthread.php?t=754924 __________________ Suzuki DR 250S '91 (98500 km and going!) Honda Transalp 600 '92 http://dr250.blogspot.com/ http://suzukidr250s.123.st

04-17-2012, 08:11 PM	#622
Lasherman Ah Sh!t! Joined: Apr 2010 Location: Turlock, Ca Oddometer: 196	Some more Pics for us DR freaks... These were taken during Warped Vlll Getting ready to ride in the rain and snow. Got better later on.. This is on the Rencon Trail Cannell Trail

06-02-2012, 11:38 AM	#623
dankatz Gnarly Adventurer Joined: Mar 2008 Location: Boston, MA Oddometer: 263	Lowered? Trying to get my wife to ride. She did the MSF course and have ridden maybe a total of 5 times after it. We sold the ninja 250 and got a Monster 696 a couple of years ago, but she is too afraid. Was thinking of lowering the 1995 DR350SE so she could use it. I am 5'8" and she is 5'5 or 5'6" with a long inseam, so am thinking of the Kouba 1.5" lower link (#1) so I could still ride it comfortably. Does anyone have any pictures of a lowered bike? How much does it affect handling or off road prowess? Should I invest in Corbin instead? Thanks! Dani

09-13-2012, 06:37 PM	#625
FlyingWman Gnarly Adventurer Joined: Jul 2009 Location: Great lakes state Oddometer: 201	1999X __________________ ___________________ 1999 DR350X 1982 GS750T

02-05-2012, 07:37 PM	#619
Lasherman Ah Sh!t! Joined: Apr 2010 Location: Turlock, Ca Oddometer: 196	More fun than watching the firs half of the Superbowel. ooooh Lookie! Some mud! Who needs a kickstand when you have a rut with mud? Need I say more?

06-03-2012, 08:30 AM	#624
plugeye mc caregiver Joined: May 2007 Location: Garland, Texas Oddometer: 2,606	dr350sex

10-01-2012, 10:04 AM	#626
Jeff@TheQuadShop TAT survivor Joined: Nov 2004 Location: Crestwood, Kentucky Oddometer: 4,437	Who is this Jesse that lots of people refer to? __________________ 1998 RMX 250 singletrack bike 96 XR600 adventure bike KY state Vet A offroad champion TAT and TWVT survivor

10-01-2012, 10:07 AM	#627
z@ch Turn it up to eleven Joined: Apr 2008 Location: Tejas Norte Oddometer: 4,526	Jesse Kientz, DR guru http://www.kientech.com/

11-04-2012, 06:55 PM	#628
Lasherman Ah Sh!t! Joined: Apr 2010 Location: Turlock, Ca Oddometer: 196	Some more DR porn......

11-05-2012, 04:00 PM	#629
jaredyates Adventurer Joined: Jun 2008 Location: Hickory, NC Oddometer: 54	I've recently sold my DR250, but one of the leftovers that I have is a 31mm pumper carb off of a dirt DR250. Is anyone looking for one? I got it from an ebay seller and never tried to install it, so I'm not sure how well it works or what it takes to get it onto a street bike. Folks say that these can wear out, but I don't really know how to measure this one to see if it has worn out or not. I have precision measuring tools and can put them to use with guidance of what to measure.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: .
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode