ManRacks.com 1-855-GR8-Racks - Page 51

Badger · 10-29-2012, 06:32 PM

Love the Rack, gonna see if I can dremel a bit off the left rear mount to use my helmet lock again. Other than that, AWESOME rack!!

jungleplant · 10-29-2012, 08:12 PM

Quote:

Originally Posted by Badger

Love the Rack, gonna see if I can dremel a bit off the left rear mount to use my helmet lock again. Other than that, AWESOME rack!!

Badger we give no concern to that lock because they don't work, don't ruin the rack for that just get a paddle lock but they don't work either,

jungleplant · 11-02-2012, 11:50 AM

siyeh · 11-04-2012, 02:48 PM

Hello, ManRacks. I have been perusing your EBay site. I see a neat little set of stainless steel tie downs for a 650L. They fit on the forks and is a neat place to attach a strap. Will these fit a 2013 CRF250L?

If they don't, will you be producing some for the CRF250L?

They look really KOOL

thank you

jungleplant · 11-04-2012, 03:01 PM

Quote:

Originally Posted by siyeh

Hello, ManRacks. I have been perusing your EBay site. I see a neat little set of stainless steel tie downs for a 650L. They fit on the forks and is a neat place to attach a strap. Will these fit a 2013 CRF250L?

If they don't, will you be producing some for the CRF250L?

They look really KOOL

thank you

no but we do have them for your bike

jungleplant · 11-06-2012, 12:17 PM

Alaskajeff · 11-06-2012, 04:23 PM

Quote:

Originally Posted by jungleplant

VERY NICE Mike! Any progress on a beefier version of my XR600 rack?

jungleplant · 11-06-2012, 04:31 PM

Quote:

Originally Posted by Alaskajeff

VERY NICE Mike! Any progress on a beefier version of my XR600 rack?

Hi Jeff how have ya been , up there with all those salmon and bears. haven't got it figured out yet , that other fender kinda tossed me for a loop , i just don't like the way it goes under the seat , i wish i could make something like the xr650r bridge support then it would be on for sure, until then its just

its a nightmare , here take a look
">

jungleplant · 11-14-2012, 08:02 AM

">

Badger · 11-15-2012, 07:14 AM

I don't have enough good this to say about ManRacks!!

The quality of the products and the customer service (before, during and after) is superior!!

Mike is tops in my book. Had a question after the sale and got a response in a matter of minutes!!

I cut a little notch to allow me to use my helmet lock. I needed it to open all the way to get it in there. Awesome rack!!

absoluteclint · 12-05-2012, 02:30 PM

Just wanted to give Mike at Manracks a little "bump"...

I had heard good things from some of the XRL riders about his customer service and product quality... I just placed an order with him today... Mike has been very responsive at answering back-forth questions all day and as soon as my PayPal payment went through this afternoon he got my items shipped. Pricing is reasonable with free holiday shipping!

I will follow up upon receipt of my SD rack, hoglegs, case saver, and tie downs. Looking forward to installing it all.

Thanks Mike

Ooh and by the way... A few pages back you asked about an XRL rider from San Fran named Steve... You may have already figured out his ADV name but if not I'm pretty sure you're talking about mcma111. He's a very helpful source on the XRL page.

Alaskajeff · 02-04-2013, 01:05 PM

Hey Mike, where ya been brother?

You've been pretty quiet lately. You must have some TOP SECRET project keeping you busy

OR just the mid winter blues? Maybe you are a 49ers fan...........Anyhoo, I've recently done some work to the XR600 #001 rack. It came out pretty well, for having a hack like me doing it. I'll be sending some pics real soon. Here is a teaser shot to keep you guessing. Notice the broken mounting tab by the signal? Just to clarify the broken tab was NOT a MANRACKS product defect in any way, rather operator error on MY PART! Hope things are well. Jeff

jungleplant · 02-04-2013, 03:25 PM

Quote:

Originally Posted by Alaskajeff

Hey Mike, where ya been brother?

You've been pretty quiet lately. You must have some TOP SECRET project keeping you busy

OR just the mid winter blues? Maybe you are a 49ers fan...........Anyhoo, I've recently done some work to the XR600 #001 rack. It came out pretty well, for having a hack like me doing it. I'll be sending some pics real soon. Here is a teaser shot to keep you guessing. Notice the broken mounting tab by the signal? Just to clarify the broken tab was NOT a MANRACKS product defect in any way, rather operator error on MY PART! Hope things are well. Jeff

Hey Jeff how ya been , ya winter sucks but got 2 cords of cherry wood in the shop to get us through, the 600 needs a good rack, its been giving me fits, , you got the cure

been working on the Milwaukee porta band stands , gonna have one for all porta band saw that they make , its our most used tool in the shop so i am gonna spread the LOVe brutha , check it out

Alaskajeff · 02-05-2013, 12:06 PM

brutha , check it out

SAWEEEEEET!!!

Alaskajeff · 02-06-2013, 12:36 AM

Finished product......

This is how I plan to attach the roto pac THIS YEAR. I think the mods I made will help.

10-29-2012, 06:32 PM	#751
Badger Gnarly Adventurer Joined: Jul 2004 Location: Slaughter, LA Oddometer: 304	Love the Rack, gonna see if I can dremel a bit off the left rear mount to use my helmet lock again. Other than that, AWESOME rack!! __________________ Je chasse le chien Honey Badger Don't Give a Shit

11-02-2012, 11:50 AM	#753
jungleplant ^OP Motorcyle Stuff Joined: Jul 2009 Location: ManRacks, California Oddometer: 1,791	Honda XR650R rotopax rack __________________ http://www.manracks.com

11-04-2012, 02:48 PM	#754
siyeh Lawn Nazi Joined: Dec 2005 Location: Evansville, Wisconsin Oddometer: 1,080	Hello, ManRacks. I have been perusing your EBay site. I see a neat little set of stainless steel tie downs for a 650L. They fit on the forks and is a neat place to attach a strap. Will these fit a 2013 CRF250L? If they don't, will you be producing some for the CRF250L? They look really KOOL thank you __________________ A little ride to Alaska A Phantom Ramble 18 days on a Versys

11-06-2012, 12:17 PM	#756
jungleplant ^OP Motorcyle Stuff Joined: Jul 2009 Location: ManRacks, California Oddometer: 1,791	HONDA CRF250L Rubicon utility BBQ rack __________________ http://www.manracks.com

11-14-2012, 08:02 AM	#759
jungleplant ^OP Motorcyle Stuff Joined: Jul 2009 Location: ManRacks, California Oddometer: 1,791	"> __________________ http://www.manracks.com

11-15-2012, 07:14 AM	#760
Badger Gnarly Adventurer Joined: Jul 2004 Location: Slaughter, LA Oddometer: 304	I don't have enough good this to say about ManRacks!! The quality of the products and the customer service (before, during and after) is superior!! Mike is tops in my book. Had a question after the sale and got a response in a matter of minutes!! I cut a little notch to allow me to use my helmet lock. I needed it to open all the way to get it in there. Awesome rack!! __________________ Je chasse le chien Honey Badger Don't Give a Shit

12-05-2012, 02:30 PM	#761
absoluteclint Gnarly Adventurer Joined: Apr 2012 Location: North Carolina foothills Oddometer: 143	Just wanted to give Mike at Manracks a little "bump"... I had heard good things from some of the XRL riders about his customer service and product quality... I just placed an order with him today... Mike has been very responsive at answering back-forth questions all day and as soon as my PayPal payment went through this afternoon he got my items shipped. Pricing is reasonable with free holiday shipping! I will follow up upon receipt of my SD rack, hoglegs, case saver, and tie downs. Looking forward to installing it all. Thanks Mike Ooh and by the way... A few pages back you asked about an XRL rider from San Fran named Steve... You may have already figured out his ADV name but if not I'm pretty sure you're talking about mcma111. He's a very helpful source on the XRL page.

02-04-2013, 01:05 PM	#762
Alaskajeff Studly Adventurer Joined: Feb 2011 Location: Palmer, ALASKA Oddometer: 688	Hey Mike, where ya been brother? You've been pretty quiet lately. You must have some TOP SECRET project keeping you busy OR just the mid winter blues? Maybe you are a 49ers fan...........Anyhoo, I've recently done some work to the XR600 #001 rack. It came out pretty well, for having a hack like me doing it. I'll be sending some pics real soon. Here is a teaser shot to keep you guessing. Notice the broken mounting tab by the signal? Just to clarify the broken tab was NOT a MANRACKS product defect in any way, rather operator error on MY PART! Hope things are well. Jeff __________________ Jeff Reichel Palmer, Alaska 1 Tim 6:11-12 "FIGHT the GOOD Fight" funinak@mtaonline.net PLATED 88 XR600R & 92 FATBOY (in rebuild status)

02-05-2013, 12:06 PM	#764
Alaskajeff Studly Adventurer Joined: Feb 2011 Location: Palmer, ALASKA Oddometer: 688	brutha , check it out SAWEEEEEET!!! __________________ Jeff Reichel Palmer, Alaska 1 Tim 6:11-12 "FIGHT the GOOD Fight" funinak@mtaonline.net PLATED 88 XR600R & 92 FATBOY (in rebuild status)

02-06-2013, 12:36 AM	#765
Alaskajeff Studly Adventurer Joined: Feb 2011 Location: Palmer, ALASKA Oddometer: 688	Finished product...... This is how I plan to attach the roto pac THIS YEAR. I think the mods I made will help. __________________ Jeff Reichel Palmer, Alaska 1 Tim 6:11-12 "FIGHT the GOOD Fight" funinak@mtaonline.net PLATED 88 XR600R & 92 FATBOY (in rebuild status)

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: .
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode