ADVrider

Go Back   ADVrider > Riding > Racing
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 12-06-2012, 08:04 PM   #76
biensur22
Gnarly Adventurer
 
biensur22's Avatar
 
Joined: Oct 2011
Location: San Diego, CA
Oddometer: 179
*Subscribed*

I just picked up a 1998 620 Adv and hope to ride the M1k as well. Good luck!
biensur22 is offline   Reply With Quote
Old 12-06-2012, 08:21 PM   #77
Baja Dad
Beastly Adventurer
 
Baja Dad's Avatar
 
Joined: Jan 2011
Location: Norco California
Oddometer: 1,893
Quote:
Originally Posted by biensur22 View Post
*Subscribed*

I just picked up a 1998 620 Adv and hope to ride the M1k as well. Good luck!
Sounds good !!!!
where did you find it ??
__________________
2014 support: GPR,IMS Aurora Rally Kriega, Raiden LS2,100Goggles,SIDI,Seat Concepts, Rally Raid Products UK,Precision Concepts, MX1West,Dunlop
Baja Dad is offline   Reply With Quote
Old 12-06-2012, 08:26 PM   #78
biensur22
Gnarly Adventurer
 
biensur22's Avatar
 
Joined: Oct 2011
Location: San Diego, CA
Oddometer: 179
Quote:
Originally Posted by Baja Dad View Post
Sounds good !!!!
where did you find it ??
It's got an odd provenance in the SD area, but I picked it up from a fellow SD adventure rider (local forum) in El Centro, CA. It's been registered non-op since 2000, so I've got some work to do to get it up to snuff. It runs well, very well; I just don't want any problems with parts that have degraded from sitting for 12 years.
biensur22 is offline   Reply With Quote
Old 12-08-2012, 10:29 PM   #79
Goofy Footer
Gnarly Adventurer
 
Joined: Jan 2011
Location: San Diego
Oddometer: 458
Quote:
Originally Posted by biensur22 View Post

I just picked up a 1998 620 Adv and hope to ride the M1k as well. Good luck!
...
Goofy Footer is offline   Reply With Quote
Old 12-09-2012, 04:13 PM   #80
biensur22
Gnarly Adventurer
 
biensur22's Avatar
 
Joined: Oct 2011
Location: San Diego, CA
Oddometer: 179
what's your plan for the roadbook mount? are you gonna strap GPS to it as well or use a ram mount off the bars?
biensur22 is offline   Reply With Quote
Old 02-18-2013, 12:13 PM   #81
Maineroot OP
Gnarly Adventurer
 
Joined: May 2012
Location: Austin Texas
Oddometer: 141
Ico magnet

I'm hooking up the ICO to the roadbook tower today.

I could not find the magnet that the stock ODO is using as a pickup. Is it one of the bolts that holds the rotor on?

I used a metal grommet to test each bolt to see if there was any magnetic activity- but could not find any difference in them.

I'd rather not mess with epoxying a magnet onto the wheel.

Anyone have any advice? or am I missing something.
__________________
#34 MX1K
TEAM GREENWOOD: Kali Protectives, Hammer Nutrition
Maine Root Handcrafted Beverages, Darco Boot, ATOMIC MOTO,
Klim Riding Gear, Flexx Bars, Seat Concepts Seats, CJ DESIGNS PEGS, FORMA
BOOTS, Tj's Cycle, Austin TX
Maineroot is offline   Reply With Quote
Old 02-18-2013, 02:22 PM   #82
wrk2surf
on the gas or brakes
 
wrk2surf's Avatar
 
Joined: Dec 2007
Location: THE exact center of California/Bass lake/Yosemite
Oddometer: 6,455
Doesnt your stock speedometer/tripmaster have a handlebar switch or ability to put one on??? What im getting at is cant you use the stock speedo for navagation? I used my 03 Speedo that on the trip 2 function where mileage can be adjusted up or down when needed.
__________________
Thanks for the 2015 support: BELL HELMETS, SCOTT USA, Kriega USA, SEATCONCEPTS.COM , Galfer USA, Carbon-pro.com, GPR stabilzers, Sidi/Motonation, Masters paint and body, Magura , Motolab , Loctite and Dunlop tires .
wrk2surf is offline   Reply With Quote
Old 02-18-2013, 02:51 PM   #83
Baja Dad
Beastly Adventurer
 
Baja Dad's Avatar
 
Joined: Jan 2011
Location: Norco California
Oddometer: 1,893
Just add a Bolt on the side where you removed the 2nd dic from. Run your ICO down that fork leg and mount the
pick up.( that is what I did last year )
I had the stock unit + (1-ICO) + (1 Trail Tech Endurance) worked OK
This year I will run the stock unit + (2-ICO) units for my old eyes
__________________
2014 support: GPR,IMS Aurora Rally Kriega, Raiden LS2,100Goggles,SIDI,Seat Concepts, Rally Raid Products UK,Precision Concepts, MX1West,Dunlop
Baja Dad is offline   Reply With Quote
Old 02-18-2013, 03:14 PM   #84
Maineroot OP
Gnarly Adventurer
 
Joined: May 2012
Location: Austin Texas
Oddometer: 141
Quote:
Originally Posted by Baja Dad View Post
Just add a Bolt on the side where you removed the 2nd dic from. Run your ICO down that fork leg and mount the
pick up.( that is what I did last year )
I had the stock unit + (1-ICO) + (1 Trail Tech Endurance) worked OK
This year I will run the stock unit + (2-ICO) units for my old eyes
OK- I can do that.

That makes it easy. Now to find a nice magnetic bolt.

Anyone have a link to that?
__________________
#34 MX1K
TEAM GREENWOOD: Kali Protectives, Hammer Nutrition
Maine Root Handcrafted Beverages, Darco Boot, ATOMIC MOTO,
Klim Riding Gear, Flexx Bars, Seat Concepts Seats, CJ DESIGNS PEGS, FORMA
BOOTS, Tj's Cycle, Austin TX
Maineroot is offline   Reply With Quote
Old 02-18-2013, 03:21 PM   #85
Maineroot OP
Gnarly Adventurer
 
Joined: May 2012
Location: Austin Texas
Oddometer: 141
Quote:
Originally Posted by wrk2surf View Post
Doesnt your stock speedometer/tripmaster have a handlebar switch or ability to put one on??? What im getting at is cant you use the stock speedo for navagation? I used my 03 Speedo that on the trip 2 function where mileage can be adjusted up or down when needed.
Good question. I did not know about the stock odo function. I just went with the setup that Santa sent me from RMS.

Roadbook
Bracket
ICO

I'm just about done with the setup. I just need to make a decision about how to hardwire in these components.

There is a dedicated molex pigtail for GPS/Roadbook on the stock wiring harness.

Anyone have objections to tying into that circuit? Or would a dedicated fuse protected circuit be recommended?
__________________
#34 MX1K
TEAM GREENWOOD: Kali Protectives, Hammer Nutrition
Maine Root Handcrafted Beverages, Darco Boot, ATOMIC MOTO,
Klim Riding Gear, Flexx Bars, Seat Concepts Seats, CJ DESIGNS PEGS, FORMA
BOOTS, Tj's Cycle, Austin TX
Maineroot is offline   Reply With Quote
Old 02-18-2013, 04:50 PM   #86
roadracer
Gnarly Adventurer
 
roadracer's Avatar
 
Joined: Sep 2004
Location: San Francisco
Oddometer: 334
I don't know about the 640adv, but the KTMs I've seen have all had the magnet in the rotor itself, it's not one of the bolts. It's in the corner of one of the cut out areas and retained by a little circlip.
roadracer is offline   Reply With Quote
Old 02-18-2013, 07:11 PM   #87
wrk2surf
on the gas or brakes
 
wrk2surf's Avatar
 
Joined: Dec 2007
Location: THE exact center of California/Bass lake/Yosemite
Oddometer: 6,455
thats on the smaller 270mm rotors used on 450s 525's and 625 sxc's where the pickup is in the caliper mount.. I have onel like that.. the larger 300 and 320 mm used on LC4s and adventures have different pickup setups
__________________
Thanks for the 2015 support: BELL HELMETS, SCOTT USA, Kriega USA, SEATCONCEPTS.COM , Galfer USA, Carbon-pro.com, GPR stabilzers, Sidi/Motonation, Masters paint and body, Magura , Motolab , Loctite and Dunlop tires .
wrk2surf is offline   Reply With Quote
Old 02-19-2013, 01:58 AM   #88
640 Armageddon
-oo-
 
640 Armageddon's Avatar
 
Joined: Mar 2009
Location: Greece
Oddometer: 2,020
My setup inculdes two IMO's. I wanted to have one pick up magnet on each side in order to make sure that if one side gets damaged I do not loose both pick up magnets.

I have used a man made bracket that bolts behind the rotor bolts (in the inside of the hub) and there I use an M8 Touratech screw magnet. That is on the brake side.
One the other side, I just drilled and tap the hub and put the pick up in the fork bolts using another man made elbow plate.

Can take some pics if you want to show the assemblies.

Of course as BajaDad said, if you have the second disc removed it is very easy to bolt a magnet there. Very nice and clean.

For Magnetic Touratech bolts see here,

http://www.touratech-usa.com/Store/P...crew-12mm-long

Although you can make your own if you are mechanically inclined with better magnets that do not demagnetize so easy over time ...

D.
__________________
Aurora Rally Equipment
"Do or Do Not. There is No Try" - Yoda
640 Armageddon is online now   Reply With Quote
Old 02-20-2013, 03:18 PM   #89
Maineroot OP
Gnarly Adventurer
 
Joined: May 2012
Location: Austin Texas
Oddometer: 141
I'm going to thread in a rotor bolt through the hole in one of these.

http://www.rare-earth-magnets.com/c-...g-magnets.aspx

Looks like it would work.
__________________
#34 MX1K
TEAM GREENWOOD: Kali Protectives, Hammer Nutrition
Maine Root Handcrafted Beverages, Darco Boot, ATOMIC MOTO,
Klim Riding Gear, Flexx Bars, Seat Concepts Seats, CJ DESIGNS PEGS, FORMA
BOOTS, Tj's Cycle, Austin TX
Maineroot is offline   Reply With Quote
Old 02-24-2013, 11:39 PM   #90
640 Armageddon
-oo-
 
640 Armageddon's Avatar
 
Joined: Mar 2009
Location: Greece
Oddometer: 2,020
Quote:
Originally Posted by Maineroot View Post
I'm going to thread in a rotor bolt through the hole in one of these.

http://www.rare-earth-magnets.com/c-...g-magnets.aspx

Looks like it would work.
Remember to check the clearance with the brake caliper. The bolt clearance is very tight. The Touratech magnetic bolt for example would interfere with the break caliper
__________________
Aurora Rally Equipment
"Do or Do Not. There is No Try" - Yoda
640 Armageddon is online now   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 01:37 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014