K&N New Product Release: KT-9907 High-Flow Air Filter, KTM 990 Adventure

[boulder]

OK unifilter have now finished there final product, I have one in my bike now and am very happy with it.
Here is the final design.
Here you can see both filters the inner has the spring and the trumpet from the TB fitted on the left and you can see the right side with the spring ready to be fitted.




Once you have both Trumpets in the inner filter just tighten the reusable cable ties up so the filter is snug. Place the front Trumpet on and lock in to place and repeat with the rear Trumpet.


Now fit the orange outer filter over the inner and lock the velcro strap.



Everything else is the same as my first post. These filters are now in production.

[boulder]

Originally Posted by The Griz

Nice! Intriguing. How does it seal around the throttle bodies though? And some more info in the watertight seal you speak of would be much appreciated... Thanks! Looks very good so far. I would just want to make sure it seals properly. I'm still going to run my K&N that's on the way, but....

The watertight seal is a seal that fits into the top of the airbox to replace the rubber part of the standard paper filter. The final version Seals around throttle bodies with reusable cable ties.

[The Griz]

Originally Posted by boulder

The watertight seal is a seal that fits into the top of the airbox to replace the rubber part of the standard paper filter. The final version Seals around throttle bodies with reusable cable ties.

Thanks for the info and great pics! I have to say that this unifilter setup rivals the rottweiler setup in so many ways I don't even know where to begin!

How long until I can order it on the Unifilter Australia website?

[Chop Chop]

Are unifilter advising to oil both inner and outer or just the outer cover?

[mousitsas]

I think the orange crush subforum of advrider is lately undergoing a filtering craze.

In the meantime, the rest of us who leave our motors breath properly, enjoy the full shebang of how wonderfully said motor spins up and how good its airbox plenum and stock snorkel do their job, by just using DNA and K&N and BMC etc filters

PS
I am sure that the 'end of the world' bike will have twin UNIs plus another UNI instead of snorkel plus a stock paper filter, while the whole bike is wrapped in a plastic bag.

[pdxmotorhead]

Hard to tell from the pic,, is it still a velocity stack? Or is that a straight breather pipe?

Dave

[MortimerSickle]

Also hard to tell from the pic: is the center section open, so each cylinder can draw from the entire filter? or does the center section separate the sides?

[Speedzter]

The Uni filter looks like it would give you the option to run with or without the Airbox lid .

Boulder, it might be worth starting a seperate thread on the Uni Filter.

Cheers

[boulder]

Originally Posted by Speedzter

The Uni filter looks like it would give you the option to run with or without the Airbox lid .

Boulder, it might be worth starting a seperate thread on the Uni Filter.

Cheers

Have started new thread Under Unifilter will answer your questions there.

[AJ..]

Hi,

will the 990 K&N airfilter fits the 950adv?

cheers

[MortimerSickle]

Originally Posted by AJ..

Hi,

will the 990 K&N airfilter fits the 950adv?

cheers

Sort of.

I just put one in my 950. the holes don't quite line up, but the filter has enough give to allow a fit.

The carb mouth pulls to one side in the seal, but I don't think it leaks. I will check for signs of leakage after I have a few miles on it (I don't expect to find any).

[AJ..]

ok great!!

that's all I need to hear.As I've already deposit on the order and will confirm with them tomoro with the ordering,shud take about 2weeks or so to arrive.
I just bought a used 950 and milege just hit 100k.It was fitted with akra cans,but strangely,the previous owner said the mech dump some aftermarket filter and use back a new stock airfilter.

How can that actually makes the whole thing breathe.