ADVrider

Go Back   ADVrider > Gear > Vendors
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 04-15-2013, 09:31 AM   #61
SpeedyR
SE in the SE
 
Joined: Aug 2005
Location: ATL, GA
Oddometer: 824
just wanted to post so i can keep up with the jetting. looking forward to getting the filter for my SE.
SpeedyR is offline   Reply With Quote
Old 04-15-2013, 02:16 PM   #62
gefr
Life is a trip
 
gefr's Avatar
 
Joined: Nov 2005
Location: East Med, Greece
Oddometer: 3,783
What air filter suits the 950 Adv?

The ITG JC30/65 "angular" fits, or do you suggest the sausage type? And is the trumpet cutting necessary?
Cheers.
gefr is offline   Reply With Quote
Old 04-15-2013, 02:28 PM   #63
Sporting Wood OP
I <3 Energizer Bunny
 
Sporting Wood's Avatar
 
Joined: Oct 2011
Location: Horneytown, NC
Oddometer: 891
Quote:
Originally Posted by gefr View Post
The ITG JC30/65 "angular" fits, or do you suggest the sausage type? And is the trumpet cutting necessary?
Cheers.
Standard oval or "angular" fits fine with no modifications on ADV and SM. Its only the SE or SM-R that require the sausage or domed version and need their intake velocity stacks trimmed. Either work well.
Sporting Wood is offline   Reply With Quote
Old 04-16-2013, 03:29 PM   #64
gaspipe
Wandering Soul
 
gaspipe's Avatar
 
Joined: Jul 2004
Location: Pickwick Lake, Tennessippi
Oddometer: 11,352
I'm in. Tired of wresslin' that damned airbox too.

__________________
gaspipe [the original]

Hair of the dog....
gaspipe is offline   Reply With Quote
Old 04-16-2013, 04:38 PM   #65
vwboomer
Buffoon
 
vwboomer's Avatar
 
Joined: Feb 2008
Location: WI
Oddometer: 9,612
Got the filter set up today. Thanks

In all actuality I will probably wait a week or two to get it on. working lots of hours and feebly attempting to do a bath remodel at the same time

I doubt I have stock jets, so will wait until I pull it apart to order any. Probably use a set of 42 pilots until after the trip, the 45's after for more power/screw economy. I normally got 35mpg with the current set up - can't be much worse than that.

So you're generally not running a richer jet on the rear cylinder? Thought normally it was a little richer due to the heat......
__________________

vwboomer is offline   Reply With Quote
Old 04-16-2013, 05:49 PM   #66
Sporting Wood OP
I <3 Energizer Bunny
 
Sporting Wood's Avatar
 
Joined: Oct 2011
Location: Horneytown, NC
Oddometer: 891
Quote:
Originally Posted by gaspipe View Post
I'm in. Tired of wresslin' that damned airbox too.


Sporting Wood is offline   Reply With Quote
Old 04-16-2013, 06:20 PM   #67
Meathead
tin man
 
Meathead's Avatar
 
Joined: Jun 2004
Location: Upstate SC
Oddometer: 16,659
Meathead is offline   Reply With Quote
Old 04-16-2013, 08:54 PM   #68
Thumper996
Studly Adventurer
 
Thumper996's Avatar
 
Joined: Jun 2009
Oddometer: 592
Look what showed up today, weekend project forth coming. Luckily i already have most everything already off the bike from recent valve check.



Thumper996 is offline   Reply With Quote
Old 04-17-2013, 08:41 AM   #69
Sporting Wood OP
I <3 Energizer Bunny
 
Sporting Wood's Avatar
 
Joined: Oct 2011
Location: Horneytown, NC
Oddometer: 891
Quote:
Originally Posted by vwboomer View Post
Got the filter set up today. Thanks

In all actuality I will probably wait a week or two to get it on. working lots of hours and feebly attempting to do a bath remodel at the same time

I doubt I have stock jets, so will wait until I pull it apart to order any. Probably use a set of 42 pilots until after the trip, the 45's after for more power/screw economy. I normally got 35mpg with the current set up - can't be much worse than that.

So you're generally not running a richer jet on the rear cylinder? Thought normally it was a little richer due to the heat......
Nope, I run the same mains though I'm in the minority. Most everyone goes one or two up on the rear. Intake runs are unequal and there is an argument for heat in the rear...though the motor is water cooled.

35 isn't too bad if you're spanking it. Leisurely touring and yeah, not so great. This is more often than not caused by too high a float height. I bet its set at the factory 3mm? Guys generally bump the jets and raise the needle making it very rich through the bottom end. Let us know what you find when you dig into it...and good luck with the bath remodel.
Sporting Wood is offline   Reply With Quote
Old 04-17-2013, 03:11 PM   #70
blublapp
Adventurer
 
Joined: Jan 2012
Location: Germany
Oddometer: 19
So guys here are the facts:

Look at the dyno graphs! I'm really impressed!

My jetting is: (Engine 990 SM '08)
175 mains
FP needle #2
Floatlevel 4mm
Screws at 2
Rest standard!

120.4 hp on the clutch
109.9 Nm torque on clutch

112.2 rwhp
104.6 Nm rw-torque

damn I'm not able to fit in the graphs.

Chris, please put it in. I've sendet them on mail to you...
blublapp is offline   Reply With Quote
Old 04-17-2013, 03:24 PM   #71
blublapp
Adventurer
 
Joined: Jan 2012
Location: Germany
Oddometer: 19
Torque in ft-lbs is: 81.06

for those who don't know Nm (Newtonmeters?
blublapp is offline   Reply With Quote
Old 04-17-2013, 04:00 PM   #72
Sporting Wood OP
I <3 Energizer Bunny
 
Sporting Wood's Avatar
 
Joined: Oct 2011
Location: Horneytown, NC
Oddometer: 891
Quote:
Originally Posted by blublapp View Post
So guys here are the facts:

Look at the dyno graphs! I'm really impressed!

My jetting is: (Engine 990 SM '08)
175 mains
FP needle #2
Floatlevel 4mm
Screws at 2
Rest standard!

120.4 hp on the clutch
109.9 Nm torque on clutch

112.2 rwhp
104.6 Nm rw-torque

damn I'm not able to fit in the graphs.

Chris, please put it in. I've sendet them on mail to you...
This is a beautiful raw rear wheel dyno.


Sporting Wood screwed with this post 04-18-2013 at 07:21 AM Reason: Pic changed and incorrect comment removed
Sporting Wood is offline   Reply With Quote
Old 04-17-2013, 05:14 PM   #73
gefr
Life is a trip
 
gefr's Avatar
 
Joined: Nov 2005
Location: East Med, Greece
Oddometer: 3,783
Quote:
Originally Posted by blublapp View Post
My jetting is: (Engine 990 SM '08)
175 mains
FP needle #2
Floatlevel 4mm
Screws at 2
Rest standard!
Great power output! How about your milliage?
Cheers.
gefr is offline   Reply With Quote
Old 04-17-2013, 09:04 PM   #74
avocadofarmer
Fruit Coot
 
Joined: Dec 2010
Location: Southern California
Oddometer: 252
Got mine today, looks great! Thanks for setting this all up Sporting Wood!

Hopefully nothing bad will happen with my stock exhausts...we'll see.
avocadofarmer is online now   Reply With Quote
Old 04-17-2013, 10:53 PM   #75
blublapp
Adventurer
 
Joined: Jan 2012
Location: Germany
Oddometer: 19
About the mileage I'm pretty happy.

Got 6.3l/100km, this is about 37,4mpg...

Was a 280km ride with highway, towns and and lots of speed

About the third clip: Think this will lower my mileage... I thougt about 0.5 more on the screws, I have a longer choke time now.

And next time I'm at the carbs I'll put my powerblades in
blublapp is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 06:31 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014