ADVrider

Go Back   ADVrider > Bikes > GSpot > GS Boxers
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 11-27-2007, 09:25 PM   #1
JimVonBaden OP
"Cool" Aid!
 
JimVonBaden's Avatar
 
Joined: Feb 2005
Location: Alexandria, VA
Oddometer: 50,579
HID Conversion on a 12GS (pictorial)

After many many promises, I decided to do a short pictorial on how to install a set of HID lights in my R1200GS. This pictorial is done with lots of extra parts removed for clarity. I wont be telling you what tools to use, or torques. This type of pictorial doesn’t lend itself well to it, but you should easily be able to do what I did.


Here are the lights in the box. Mine were the fat ballasts, with the igniters built in. I have done the ones without the ballast built in, and they are definitely easier to mount, though basically in the same place.



I removed the instruments for the job to make it easier to see, but it is definitely not needed. Here are the High (left) and low (right) covers. Just pop the caps off by twisting them counterclockwise.



Here is a cap before drilling the 23mm hole. I used a Dremmel tool to do mine.



Here is the same cap after removing the material. Interestingly, it is exactly the same size as the indents in the caps. I bet you know why?



Simply push the wires through the hole, then pull the grommet in place. They recommend adding some sealant, but I didn’t. I figure they will seal just fine as is.



Here are both of them mounted. The wiring looks clean and secure in the caps.



Here is the right ballast mount. You can see it went to the screw holding the oil line.



This is the other mount, shown to illustrate the original shape. I bent it with pliars.



Now you can see it is a tight fit with the beak installed. But it is clean. I added some tie straps to secure the ballast to the mount, and firm it in place as well.



The right ballast fit in, and cleanly. With everything put back together, and the wiring secured, it is nearly invisible.



On the left side, the ballast goes into the same place. It is a tight fit, and you will have to play with it a bit, but it will fit. The slimmer ballast would have the advantage here.

Now lets take a look at the results:


Low HID. Clean white, but not too blue. This is the 4300 kit.

I then added a second GS, with Motolights, and compared them side-by-side.

Note that the bike on the left is completely stock with 35 watt Motolights. My bike has both HIDs, and 50 watt Motolights.



Low beam, you can see the difference here.




High beam, even more obvious.




Both bikes with Motolights and High Beams.

It seems obvious to me, especially after riding at night, that the HID lights are definitely superior, and not as susceptible to dimming at idle with Gerbings and Servos going.



Here is what the bulb looks like installed in the low beam.



Don’t forget to keep the old H7 bulbs, just in case. This procedure is completely reversible, and if an HID goes out, you can swap in the old H& in minutes.

Jim
JimVonBaden is offline   Reply With Quote
Old 11-27-2007, 09:33 PM   #2
NBeener
Beastly Adventurer
 
Joined: Aug 2007
Location: Fort Collins, Colorado
Oddometer: 1,521
Nice walk-through, Jim. Thanks.
NBeener is offline   Reply With Quote
Old 11-27-2007, 09:38 PM   #3
sweptwingnut
The Nut
 
sweptwingnut's Avatar
 
Joined: Jul 2006
Location: Spokane, WA
Oddometer: 156
Talking

AWESOME!!!!
__________________
2006 1200GS for me
2012 F650GS (twin) for my wife

http://www.twowheelfemales.com
sweptwingnut is offline   Reply With Quote
Old 11-27-2007, 09:44 PM   #4
NBeener
Beastly Adventurer
 
Joined: Aug 2007
Location: Fort Collins, Colorado
Oddometer: 1,521
Incidentally....

Quote:
Originally Posted by JVB
and not as susceptible to dimming at idle with Gerbings and Servos going.
Presumably, that's their reduction in draw vs. the halogens, but ... that dimming at idle on the halogens, in theory, was also shortening their lifespan (I wonder if there was a connection between voltage drop at idle and the H7 bulbs you folks have gone through).

The filament has to burn at a certain heat before the halogen gas forces the suspended particulate matter back ON to the filament, increasing its lifespan. If that cycle breaks (voltage drops), the lifespan shortens.

Hmmmm.
NBeener is offline   Reply With Quote
Old 11-27-2007, 10:12 PM   #5
michnus
Vagabond, yes I try!
 
michnus's Avatar
 
Joined: Apr 2005
Location: South Africa
Oddometer: 1,098
I have done a HID conversion on my 1200, but only the low beam, I realised straight on, the low beam is to bright for everyday use, it irritates drivers in front of you, also because the 1200 headlight just sits high enough to reflect right into a cars rear view mirror, people were constanly adjusting their rear view mirrors.

Subsequently have moved it to the high beam and still having a normal H7 globe in the low beam.
michnus is offline   Reply With Quote
Old 11-27-2007, 10:21 PM   #6
configurationspace
delooper
 
configurationspace's Avatar
 
Joined: Jan 2003
Location: Kanadia
Oddometer: 8,691
missing part to your story...

How do the electrics work?

Are your HIDs drawing straight off the battery, or are they hooked up solely to the wires for the stock lights. If so, what did it take to adapt the plugs?

and... do your lights come on before you hit the start button?
configurationspace is offline   Reply With Quote
Old 11-27-2007, 11:32 PM   #7
SocalRob
Beastly Adventurer
 
SocalRob's Avatar
 
Joined: May 2006
Location: Los Angeles @ base of Angeles Crest Hwy
Oddometer: 13,585
Quote:
Originally Posted by configurationspace
How do the electrics work?

Are your HIDs drawing straight off the battery, or are they hooked up solely to the wires for the stock lights. If so, what did it take to adapt the plugs?

and... do your lights come on before you hit the start button?
At least the new kits draw their power off the OEM headlight wiring. Its a 100 percent plug & play other than drilling out the cap like Jim did and other than having to mount the ballasts. IMO the new thin ones are worth the extra bucks. I really like that its so easy to reverse, even along side the road, should your HID or ballast ever crap out.

I haven't found the low beam too irritating to other drivers after a couple of adjustments on aiming.

Hey Jim, wasn't sure your kit would still work after the long time on the shelf
__________________
Rob

'07 White (the coolest color) GSA rider
'13 Husky Strada & '14 KTM 690 Enduro
SocalRob is online now   Reply With Quote
Old 11-28-2007, 06:25 AM   #8
volbeat22
n/a
 
Joined: Feb 2006
Oddometer: 773
From who did you buy your kit?
volbeat22 is offline   Reply With Quote
Old 11-28-2007, 06:43 AM   #9
FrisbeeR1200GS
Gnarly Adventurer
 
FrisbeeR1200GS's Avatar
 
Joined: Jul 2007
Location: Southern Ohio, and North East Wisconsin
Oddometer: 194
As mere mortals, we would be lost in the wilderness without the sage wisdom and "wrenching skills" of the Grand Master....and then he shares so unselfishly. Is He Good or What??

Naturally I'm talking about Jim V.
__________________
"Never Underestimate The Consequences Of Human Error"

FrisbeeR1200GS screwed with this post 11-29-2007 at 01:38 PM
FrisbeeR1200GS is offline   Reply With Quote
Old 11-28-2007, 07:35 AM   #10
Rick Lee
Beastly Adventurer
 
Rick Lee's Avatar
 
Joined: Apr 2007
Location: Cave Creek, AZ USA
Oddometer: 1,243
So who has put HID's in their aux. lights? My low and high beam HID's are 6000k. I think I want a contrast color in my Hella Micro DE's when I get them. I'm thinking of 3000k HID's them or maybe just amber H3 filament bulbs.
__________________
'06 K1200R
'96 993 C2
Rick Lee is offline   Reply With Quote
Old 11-28-2007, 07:43 AM   #11
Xeraux
Archvillain
 
Xeraux's Avatar
 
Joined: Sep 2006
Location: Atlanta, Georgia
Oddometer: 30,892
Quote:
Originally Posted by MikeyD
From who did you buy your kit?
http://www.vvme.com/catalog/list-s-10145-10146.html

US$55.99
__________________
Every saint has a past and every sinner has a future.

If, after I depart this vale, you ever remember me and have thought to please my ghost, forgive some sinner and wink your eye at some homely girl.
Xeraux is offline   Reply With Quote
Old 11-28-2007, 07:51 AM   #12
GB
Mod Squad
 
GB's Avatar
 
Joined: Aug 2002
Location: Toronto, ON
Oddometer: 55,811
There are 2 ways to wire the HID kits... I'll let Jim tell the story...

Just FYI: If you don't have servo/ABS, you can stash the ballasts under the tank, there's a lot of space there!!
__________________
ADV decals, patches & flag? Here
GB is offline   Reply With Quote
Old 11-28-2007, 08:10 AM   #13
Hotspice
Satellites not acquired
 
Hotspice's Avatar
 
Joined: May 2004
Location: Snow-Bound
Oddometer: 5,524
Looks good Jim..

It looks like you have a tight fit here:


Were you able to get your accessory plug on the beak back in after the ballast install?
__________________
Cyclenutz.com motorcycle accessories

Get a SmugMug account and use coupon code DwHE0pDRjpJfw to save yourself $5.
Hotspice is offline   Reply With Quote
Old 11-28-2007, 08:16 AM   #14
volbeat22
n/a
 
Joined: Feb 2006
Oddometer: 773
So are you getting a High Beam and a Low Beam - or do you now have two of the same?
volbeat22 is offline   Reply With Quote
Old 11-28-2007, 08:20 AM   #15
heetseeker
Hopelessly addicted
 
heetseeker's Avatar
 
Joined: Oct 2007
Location: Wilton CA
Oddometer: 370
That didn't take long

Thanks for the info and pics. Looked simple enough, cheap enough, and effective enough for me. There is now a set coming to me from accross the pond. With shipping: $90
heetseeker is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 02:27 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014