ADVrider

Go Back   ADVrider > Bikes > Thumpers
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 04-04-2013, 08:16 AM   #15346
2bold2getold
Beastly Adventurer
 
Joined: Dec 2011
Location: DFW TX
Oddometer: 1,258
Hanging Idle

From my experience, when you have the hanging idle problem it's because the idle circuit in your carb isn't working right ( clogged idle jet, air/fuel screw not right, idle air jet clogged, etc) and then to compensate you turn the idle speed screw up untill it is idleing on the next/mid range circuit. It's trying to get down to the idle circuit but it just can't and if it could there is nothing there to idle on. After you get the idle circuit working right, in most cases you will need to readjust the air/fuel screw after changing the idle speed screw. One will influence the other.
2bold2getold is offline   Reply With Quote
Old 04-04-2013, 10:10 AM   #15347
MrPulldown
Beastly Adventurer
 
MrPulldown's Avatar
 
Joined: Aug 2009
Location: Truckee
Oddometer: 2,474
Quote:
Originally Posted by Greg Bender View Post
Would only a new slide have seen the same improvement? I don't know because I didn't try replacing only the slide. A new slide through Rocky Mountain ATV MC is $100. An entirely new carburetor through Viperizer Racing is $216. It seemed wise to spend a little over double for the entire new carburetor, and not risk remaining wear to the carburetor body (not just the slide).

Regards,

Gregory Bender
NEw slide from Viperizer racing is only $20
__________________
94 DR 350 SE
No Load LED Flash Relay and Diode Kits for Sale
MrPulldown is offline   Reply With Quote
Old 04-04-2013, 10:34 AM   #15348
Greg Bender
Beastly Adventurer
 
Joined: Oct 2007
Location: Cave Creek, Arizona, United States
Oddometer: 1,038
Quote:
Originally Posted by MrPulldown View Post
NEw slide from Viperizer racing is only $20

Oooh...that's cheap!
Greg Bender is offline   Reply With Quote
Old 04-04-2013, 10:38 AM   #15349
Hotmamaandme
Wishing I was riding RTW
 
Hotmamaandme's Avatar
 
Joined: Jan 2006
Location: Gardnerville NV
Oddometer: 2,614
Quote:
Originally Posted by Greg Bender View Post
Viperizer Racing is $216. It seemed wise to spend a little over double for the entire new carburetor, and not risk remaining wear to the carburetor body (not just the slide).

Regards,

Gregory Bender

Good site link thanks
__________________
My screen name is kind of long. I am the "ME" part, my name is Cory.

Jimmy Lewis quote: "Those KLRs are full of potential. Just takes a rider..."
Hotmamaandme is offline   Reply With Quote
Old 04-04-2013, 01:26 PM   #15350
LawlerClan
Adventurer
 
Joined: Jan 2012
Location: Hershey, PA
Oddometer: 34
Side plastics

Quote:
Originally Posted by MrPulldown View Post
This is the Argentina ones:
http://www.ebay.com/itm/SIDE-COVERS-...#ht_349wt_1159

OEM:
http://www.ebay.com/itm/New-White-Si...ht_2318wt_1159

Maier makes some side planels which I think are the Argentina ones but I can not find them right now.

Mair rear fender:
http://www.ebay.com/itm/Suzuki-MX-Re...#ht_193wt_1397

UFO front fender:
http://www.kientech.com/UFOFrontFender.htm


I think most dirt bike front fenders that attach with four bolts will work.

Anyone tried these:

http://www.cheapcycleparts.com/produ...nt-side-panels
LawlerClan is online now   Reply With Quote
Old 04-04-2013, 02:54 PM   #15351
haggeo
Studly Adventurer
 
haggeo's Avatar
 
Joined: Aug 2005
Location: oakland, ca
Oddometer: 856
Quote:
Originally Posted by LawlerClan View Post

i saw those on thumpertalk's online store.
__________________
When the facts change, I change my mind. What do you do, sir? John Maynard Keynes



Faced with the choice between changing one's mind and proving that there is no need to do so, almost everyone gets busy on the proof." John Kenneth Galbraith



The object of life is not to be on the side of the majority, but to escape finding oneself in the ranks of the insane. Marcus Aurelius

haggeo is offline   Reply With Quote
Old 04-04-2013, 03:24 PM   #15352
kobukan
almost gnarly
 
kobukan's Avatar
 
Joined: Dec 2009
Location: Saco ME
Oddometer: 1,694
Quote:
Originally Posted by LawlerClan View Post
Those are the Maier side panels someone mentioned earlier.
__________________
'04 R1150GS, '97 R1100GS, '99 DR350, '02 DR650, '03 DR650
A Few Days Solo to Copper Canyon
A Maine Rider’s Arizona Day Trips
A Few Days Solo in Baja
kobukan is offline   Reply With Quote
Old 04-04-2013, 05:17 PM   #15353
MadChap
Gnarly Adventurer
 
MadChap's Avatar
 
Joined: Jan 2010
Location: Out of Prison
Oddometer: 411
Quote:
Originally Posted by LawlerClan View Post
I have them. Look good. Crappy mounting system, but solid once you have them on. Did I mention the mounting system is crap. Buy used originaals if you can find them.
MadChap is offline   Reply With Quote
Old 04-04-2013, 05:30 PM   #15354
mustangwagz
Gnarly Adventurer
 
mustangwagz's Avatar
 
Joined: Apr 2012
Location: Western PA
Oddometer: 242
Anyone gotta QUICK source for a kickstart shaft Oil seal? Cant find none on Flebay, and most parts store i deal with online are Slow As Molasses.
__________________
-WagZ-
'93 DR350S

My attempt to roundup Local Riders..
https://www.facebook.com/dualsportridingwesternpa
mustangwagz is offline   Reply With Quote
Old 04-04-2013, 06:06 PM   #15355
thump!
Adventurer
 
thump!'s Avatar
 
Joined: Jan 2007
Location: Northeast Tennessee
Oddometer: 882
Quote:
Originally Posted by mustangwagz View Post
Anyone gotta QUICK source for a kickstart shaft Oil seal? Cant find none on Flebay, and most parts store i deal with online are Slow As Molasses.
I haven't looked at the starter seal but seals and bearings are usually standard sizes. The seal will usually have identifying numbers molded into the rubber. Take those numbers to a bearing supplier or an autoparts dealer (NAPA is better than Autozone). There's a good chance they will have what you need on the shelf.
thump! is online now   Reply With Quote
Old 04-04-2013, 07:38 PM   #15356
_CJ
Retrogrouch
 
_CJ's Avatar
 
Joined: Dec 2010
Location: The 719, Yo.
Oddometer: 1,311
Got my DR out for the first ride of the year today. It was just around town, but this bike is just so much damn fun!

I rotated the bars forward to get a little more height out of them...what a difference. Arms are at a nice length now, sitting and standing. Might add some risers, but won't decide on that until riding on some dirt.

__________________
.
.
Moto since 2011, DR350
MTB since 1991, Full-Rigid Steel 1x8
_CJ is offline   Reply With Quote
Old 04-04-2013, 07:40 PM   #15357
redleger
Horrible Mechanic
 
redleger's Avatar
 
Joined: Jan 2013
Location: Tornado Alley, Oklahoma
Oddometer: 562
I feel the same way man. I have been riding to work the last few days, and I just love the bike. I will never get rid of it. May you enjoy many more days on yours!
__________________
2006 Suzuki DRZ 250
redleger is offline   Reply With Quote
Old 04-04-2013, 08:39 PM   #15358
2bold2getold
Beastly Adventurer
 
Joined: Dec 2011
Location: DFW TX
Oddometer: 1,258
Quote:
Originally Posted by mustangwagz View Post
Anyone gotta QUICK source for a kickstart shaft Oil seal? Cant find none on Flebay, and most parts store i deal with online are Slow As Molasses.
Ron Ayers has got it for $3.89
http://www.ronayers.com/Fiche/TypeID..._MODEL_L_M_N_P

I've ordered one a while back (still in the plastic bag). It looks like it could be a common seal. Suzuki PT# 09283-20044. writing on the seals is: A14 SD 20 27 6 HS and brand in script...Ats
2bold2getold is offline   Reply With Quote
Old 04-05-2013, 03:21 AM   #15359
Greg Bender
Beastly Adventurer
 
Joined: Oct 2007
Location: Cave Creek, Arizona, United States
Oddometer: 1,038
Quote:
Originally Posted by 2bold2getold View Post
Ron Ayers has got it for $3.89
http://www.ronayers.com/Fiche/TypeID..._MODEL_L_M_N_P

I've ordered one a while back (still in the plastic bag). It looks like it could be a common seal. Suzuki PT# 09283-20044. writing on the seals is: A14 SD 20 27 6 HS and brand in script...Ats
Just guessing here. Extrapolating the dimensions I get:

ID: 20mm
OD: 27mm
Width: 6mm

Regards,

Gregory Bender
Greg Bender is offline   Reply With Quote
Old 04-05-2013, 08:43 AM   #15360
FireDog45
Mid-life crisis sufferer
 
FireDog45's Avatar
 
Joined: Sep 2006
Location: Centerburg, Ohio
Oddometer: 577
To those who have removed the rim locks...

I pulled my rim locks (balance issues posted earlier) and now am wondering what, if anything, I should do to plug the now empty hole in the rim. My thinking is something should go there to keep the tube from pushing out like a big zit!

Irrational fear or justified concern...?
FireDog45 is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 05:49 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014