Airhead Flea Market Thread

[Voltaire]

No ...not a Bon Jovi song....
After a small airhead tank for a racer project in New Zealand.
Tank condition not that important as long as it hold fuel.
Dents not a problem.
Ideally a toaster tank but looking at budget options.
thanks
John

[SPO]

Originally Posted by villageidiot

bumpin this up further, still have stuff

Sent you a PM...

[exhaust_nut]

Originally Posted by ogriofa

I am looking for a used Master Cylinder for a 1979 R45.
Anybody?

What size (mm)? Is it the square on or round?

[k12lts]

Originally Posted by k12lts

I have a Reynolds ride-off stand from an 81 R100RT. The stand is in good shape with some wear on the bottom and decent chrome. Includes all mounting hardware, including the unobtanium bushings, except bolts and nuts (your factory ones will work).

Model number is 328, Should fit 81-84 R100.

$100 shipped in lower 48

Side stand sold, ride-off stand still available.

[Cogswell]

I have a green face Clock in my spares that I no longer need. There is a small dent on the bezel about 11:00, and typical scuffs at the raised edge. The clock runs FAST. If I remember correctly it runs about 3:1 or three revolutions per one actual minute.
Body is in great shape, no corrosion and the bulb socket and studs are in great shape.

$40 plus shipping to the lower 48.










Mike

[XTrovert]

Hi I have a Denfeld Police seat fits most R models but not the R80G/S with the rear rack (it is a tad longer).
The seat is an original BMW police stock.
Top upholstery is fine and pliable, the rear vertical panel can be either repaired or changed. The front vertical panel can be either gaffer-taped or changed. Seat pan has surface rust otherwise solid. Foam is pliable and comfy. It has the original glovebox also the orig hardware which is expensive to buy if you do not have it.
I have seen these selling on ebay for $400 buy it now when in top nick and $200 when in ok condition. Lets say $150 for this. I am in Germany right now. Postage to the US will be around $50.
Please PM if interested. I am giving this a try then it will end up on ebay if no takers. The seat owes me $150 unfortunately. That is what I paid for it :(
Inerested parties please contact me.

[XTrovert]

Hi again this is one of my stupid ideas, I bought a whole lot of these keys because I know they are as rare as hens teeth and most of them unobtainable. I thought about reproducing them and becoming a millionaire ha ha but failed abysmally because no blanks are found. Now, I found these keys in Argentina, old stock sleeping at a warehouse. In Argentina and as a rule of thumb parts are US prices x 2, so yes laugh at me I paid USD $15 per key.
These are the numbers I have: #040 #042 #045 #046 #047 #048 #049 #050 #051 #052 #053 #054 #055 #056 #060 #064 #066 #067 #068 #069
So if you are interested please let me know, we can workout something as this has been a total loss for me. I am right now in Germany. Postage should be as cheap as a standard letter but there wont be insurance...still should workout allright.
Here is a picture of the panniers and where to find the code on the latch, both stolen from the internet. I am also after a #041 top latch if you have one I am happy to trade.
Cheers

[XTrovert]

Hi I have one of these rare front fenders for a R80G/S. They fit on the front fork brace make an huge change in the bike´s stability at high speeds, ideal for tourers, highly recommended. The one for sale is in very good condition just have a few marks that get hidden by the fork tube, white unpainted. I am right now in Germany. I want $75 for it which is what it owes me, postage extra.
Here is a pic from a fellow inmate.
PM if interested. Thanks

[ogriofa]

Originally Posted by exhaust_nut

What size (mm)? Is it the square on or round?

Hey thanks for the response, its the round one 16mm
Know anybody breaking one?

[Hawk Medicine]

Hi guys,

Please check out my list of Airhead parts. All of it is good usable parts. I don't sell junk and I don't like people being mad at me! OTOH, I've included BMW part numbers where possible and I would suggest that you check my photos and an on line parts directory to make sure that you're buying what you need.

Please contact me at: mymindsok@yahoo.com I'll check back here but I'll be sure to get your message at my mailbox!

1) Lightened Flywheel from my R90/6 Functions perfectly. - $75

2) Near new EZ Clutch and BMW near new clutch cable for “S” bars. - $100 SOLD

3) /6 Airbox, Soda blasted and clean $25

4) Pair of Brembo Calipers Ready for rebuild $40

5) Corbin RS/RT seat. Good condition but ready for a recover. - $50

6) BMW RS/RT seat and surround with a good Motosport badge, solid pan, no hinges - $100

7) Airhead Connecting Rods in good condition 40.00

8) Pair of Airhead Thrust Washers. #11111256976 - $25 for the pair

9) 15mm Master Cyl Rebuild kit #32722302372 - $50.00

10) 2 sets of Nikasil Piston Rings #11251337399 - $100

11) One /5 Hub Cap. Not perfect but really nice! $25

12) One rectangular Valve Cover. Usual scrapes. Soda blasted and ready for sanding and paint. $30

13) Pair of rectangular valve covers. The usual scrapes but no major damage and they'll clean up well. $60 (These are currently selling for $116 each new!) SOLD PP

14) Rear Wheel Spacer to fit a wide tire. #36312301737 - $11.00

15) One lid seal for BMW Touring bags. New in Package. #46542300016 - Free with a purchase

16) RT Fairing mount. Soda Blasted clean and straight. $35.00

17) RS/RT lower fairing louvered panel. Brand new in plastic. - $25 SOLD PP

18) /5 Gas Cap in good condition. Kept it when I sold my /5 - $50

19) /6 Swing Arm with smooth working Driveshaft $75

20) 8 pcs Rebuildable Airhead Petcocks. Valves, fuel nipples, fuel line crossovers, etc. $50

21) One 21 pc lot of Heyco/BMW tools. All used but no crap. Have em replated for your Resto or just use em. $50

22) Farley Side Stand. This one is almost new! A few scrapes on the tip. $100

23) Shoei RF 1000. Size XL Metailc Silver/Gray. Only worn for two hours. Clean inside and out. Not a scratch on it. Includes a quick release buckle that readily removable. $150.00

24) One NOS BMW 336 Cam. Purchased in 2008 but never used. This cam predates Chinese manufacture, so don't worry about this thing flaking. This ones fron Germany! It comes with or without the DR timing gear in the photos and Fits all 1979 to 1995 engines. $150

http://s177.photobucket.com/albums/w...0SALE%20STUFF/

Also!

Modified R100RS frame.
This would make make the ultimate frame for an Airhead Cafe Racer, a very kool Scrambler or race bike. A straight, undamaged frame was gusseted to improve strength and handling and the engine was raised in the frame by flipping the front mount and installing the rear mount thru-frame. Steering lock was removed, a /6 style horn mount was added. Etc. These were popular and proven mods during the Airhead era and have also been proven on my road bike. This frame was going to be the base for my next build but the adoption of my Grandson. has changed my plans. This frame was Soda blasted clean and is currently painted gloss black and is ready to ship with clean title. $350 + Ground Shipping or best offer.

See t here:http://s177.photobucket.com/albums/w...Frame%20Build/

Modified 1976 R90/6 Frame:
This frame doesn't have the level of mods that the above R100 frame has but both the frame and the sub-frame have been gusseted and strengthened for improved handling and longevity. The engine is NOT raised but the head area has been stiffened as has the swing arm area, etc. The center stand mounts were repaired using SS inserts and are better than new. This frame does not have side braces but is otherwise identical to what you'll see through the link and is ready for paint.. All of the work on these frames was done by a master bike builder and this one is identical to the frame thats under my personal 1976 /6 R100 custom. If you want a twin shock bike that can tour with a heavy load and handle the curves, this is just the ticket! Ready to ship with a clean title. $250 + Shipping.

See it here: http://s177.photobucket.com/albums/w...ECIAL%20FRAME/

Heres my bike: http://i177.photobucket.com/albums/w...EB82010048.jpg

If you are interested in trading, I'm looking for a LWB /5 or /6 seat in good to V-good condition or a “no rust” /6 seat pan with hinges and pin. I'm also looking for a twin shock trailer hitch, trailer, or a set of /6 wire wheels or wheel hubs in good condition.

Thanks for looking!

[bmweuro]

http://www.advrider.com/forums/showt...8#post19035468

[_cy_]

Looking BMW panniers, mounts and rear Box that will fit my R80 G/S

please PM or email with details...

[Redbean]

Originally Posted by Hawk Medicine

Hi guys,

Please check out my list of Airhead parts. All of it is good usable parts. I don't sell junk and I don't like people being mad at me! OTOH, I've included BMW part numbers where possible and I would suggest that you check my photos and an on line parts directory to make sure that you're buying what you need.

Please contact me at: mymindsok@yahoo.com I'll check back here but I'll be sure to get your message at my mailbox!

1) Lightened Flywheel from an R90/6 Functions perfectly. - $100

2) Near new EZ Clutch and BMW near new clutch cable for “S” bars. - $100

3) /6 Airbox, Soda blasted and clean $25

4) Pair of Brembo Calipers Ready for rebuild $40

5) Corbin RS/RT seat. Good condition but ready for a recover. - $50

6) BMW RS/RT seat and surround with a good Motosport badge, solid pan, no hinges - $100

7) Airhead Connecting Rods in good condition 40.00

8) Pair of Airhead Thrust Washers. #11111256976 - $25 for the pair
Double Row Timing Chain

9) 14mm Master Cyl Rebuild kit #32722302372 - $50.00

10) 2 sets of Nikasil Piston Rings #11251337399 - $100

11) One /5 Hub Cap. Not perfect but really nice! $25

12) One rectangular Valve Cover. Usual scrapes. Soda blasted and ready for sanding and paint. $30

13) Pair of rectangular valve covers. The usual scrapes but no major damage and they'll clean up well. $60 (These are currently selling for $116 each new!)

14) Rear Wheel Spacer to fit a wide tire. #36312301737 - $11.00

15) One lid seal for BMW Touring bags. New in Package. #46542300016 - Free with a purchase

16) RT Fairing mount. Soda Blasted clean and straight. $35.00

17) RS/RT lower fairing louvered panel. Brand new in plastic. $25

18) Shoei RF 1000. Size XL Metailc Silver/Gray. Only worn for two hours. Clean inside and out. Not a scratch on it. Includes a quick release buckle that readily removable. $150.00

http://s177.photobucket.com/albums/w...0SALE%20STUFF/

Also!

Modified R100RS frame.
This would make make the ultimate frame for an Airhead Cafe Racer, a very kool Scrambler or race bike. A straight, undamaged frame was gusseted to improve strength and handling and the engine was raised in the frame by flipping the front mount and installing the rear mount thru-frame. Steering lock was removed, a /6 style horn mount was added. Etc. These were popular and proven mods during the Airhead era and have also been proven on my road bike. This frame was going to be the base for my next build but the adoption of my Grandson. has changed my plans. This frame was Soda blasted clean and is currently painted gloss black and is ready to ship with clean title. $350 + Ground Shipping or best offer.

See t here:http://s177.photobucket.com/albums/w...Frame%20Build/

Modified 1976 R90/6 Frame:
This frame doesn't have the level of mods that the above R100 frame has but both the frame and the sub-frame have been gusseted and strengthened for improved handling and longevity. The engine is NOT raised but the head area has been stiffened as has the swing arm area, etc. The center stand mounts were repaired using SS inserts and are better than new. This frame does not have side braces but is otherwise identical to what you'll see through the link and is ready for paint.. All of the work on these frames was done by a master bike builder and this one is identical to the frame thats under my personal 1976 /6 R100 custom. If you want a twin shock bike that can tour with a heavy load and handle the curves, this is just the ticket! Ready to ship with a clean title. $250 + Shipping.

See it here: http://s177.photobucket.com/albums/w...ECIAL%20FRAME/

Heres my bike: http://i177.photobucket.com/albums/w...EB82010048.jpg

If you are interested in trading, I'm looking for a LWB /5 or /6 seat in good to V-good condition or a “no rust” /6 seat pan with hinges and pin. I'm also looking for a twin shock trailer hitch, trailer, or a set of /6 wire wheels or wheel hubs in good condition.

Thanks for looking!

I'll take the set of valve covers and the louvered panel.

Great prices, thanks.

I spent a long time looking for an RT fairing bracket, and paid a lot more for it than the one you are selling. It was surprisingly hard to find.

Email on the way.

[Dispatcher]

Looking for a good used dash from an R90s fairing.....

I have the fairing & windshield, but need the dash section.


Also looking for mounting brackets/hardware.

Reasonable price please....

Prefer Canada, but ALL considered.

Thanks

[apt13]

http://advrider.com/forums/showthread.php?t=805903

Since I couldn't ever find any simple and clean airhead inspired shirts I liked, I decided to make my own. And thought I might make a small run for anyone else who might like them.

The shirts are printed on a super soft 100% cotton tee. They are slightly "fitted" but not quite as tight as an American Apparel shirt. They are printed using the water-based discharge method so the print is also super soft and breathable so it's not a thick gob of ink on your chest. It's also more "eco-friendly" if you are into that sorta thing.

**(the print will feel "chalky" when you get the shirt. WASH BEFORE WEARING. that chalkiness is part of the discharge and it all washes out)**

I'm hoping that if these go over well I can do more brands of bikes and iconic tank stripe styles. So consider this a "limited edition test run." haha.

$18 each. You can order the shirts at my bigcartel site:

http://apt13.bigcartel.com/