ADVrider

Go Back   ADVrider > Bikes > GSpot > GS Boxers
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 10-02-2012, 09:54 PM   #1
mmytacist OP
Adventurer
 
mmytacist's Avatar
 
Joined: Apr 2002
Location: San Jose, CA
Oddometer: 22
loss of electrical power when turning handlebars lock to lock

my fairly old but formerly holding up splendidly 2001 R1150GS with 100K miles is exhibiting an electrical gremlin. I hope someone here who lives and breathes wiring harnesses will have an aha! moment on reading this description.

When turning the handlebars lock to lock, at some point in that motion, and not always at the same point, I will lose complete electrical power for an instant, then it will all come back (lights, instrumentation, etc). But at that point it is too late of course. The bike needs to be restarted with the starter button. Not cool when you are cornering

Home safe in my garage I can grab the big wiring loom on the left side of the steering head and by gently pulling that back and forth cause the same symptoms I got while riding. So its in there somewhere... I also see the black plastic covering on that wiring loom has split in many location so that I can see the wires inside, but none appears to be frayed.

Any help appreciated.

FYI: for full disclosure, I had just finished replacing my original brake lines with SS lines. The fuel tank was off, but the only electrical connection I touched during the whole procedure was the one you disconnect to remove the fuel tank (on the right side of the bike).

Thanks
Ben
mmytacist is offline   Reply With Quote
Old 10-03-2012, 07:12 AM   #2
Terry
Beastly Adventurer
 
Terry's Avatar
 
Joined: Jun 2002
Location: Colorado Springs, Colorado
Oddometer: 1,300
It is not uncommon. The short section of harness between the ignition switch and the frame is too stiff and will eventually break. Either the wires themselves, or the switch. Mine did it so that the bike would start and run fine, but would die every time I turned the handlebars to the right. I replaced the harness and switch. Fairly easy job. There is a small set screw that holds the switch in the lock assembly. It is secured with some lock-tite, so you will need to clean that out and then have the correct size (and good quality) screwdriver available. There are some good pictures somewhere here on ADVRider. I think I removed the upper triple clamp so it was easier to get to the lock, but it may be possible to do it without.
Here is the thread from when I did it.

http://www.advrider.com/forums/showthread.php?t=569692

Terry
__________________
"The rights of every man are diminished when the rights of one man are threatened." John F. Kennedy, June 11, 1963
Terry is offline   Reply With Quote
Old 10-03-2012, 08:02 AM   #3
mmytacist OP
Adventurer
 
mmytacist's Avatar
 
Joined: Apr 2002
Location: San Jose, CA
Oddometer: 22
Excellent, thanks Terry.
Apparently I suck at searches...

Regards,
Ben
mmytacist is offline   Reply With Quote
Old 10-03-2012, 04:06 PM   #4
Bender
I can pass this guy.
 
Bender's Avatar
 
Joined: Feb 2005
Location: Cypress, Texas.
Oddometer: 33,364
Buy a new switch, the fix is very easy! Do not drill the old switch bolts out. Looks for a dot of paint on the ignition barrel, dig it out to find a magic allen head screw. Loosen the screw and the switch falls right out.
__________________
Bender™
Bender is online now   Reply With Quote
Old 10-03-2012, 07:53 PM   #5
Peka
Beastly Adventurer
 
Peka's Avatar
 
Joined: Nov 2004
Location: Brisbane, Australia
Oddometer: 1,999
On my 1100 I managed to find the section of cable where it was broken. It wasn't completely broken but enough to cause the same symptoms you have. So I just fixed the break and protected it with some split tubing.
Peka is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 11:26 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014