ADVrider

Go Back   ADVrider > Bikes > GSpot > GS Boxers
User Name
Password
Register Inmates Photos Site Rules Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Search this Thread Display Modes
Old 01-21-2013, 05:18 PM   #1
madpuma13 OP
Gnarly Adventurer
 
Joined: Feb 2011
Location: CenTex
Oddometer: 109
Altrider Crashbars Installation

Has anyone done the installation of these crashbars themselves? I am talking about their new version that doesnt have any separate brackets (other than the bracket to hold the two sides together).

I recently got them and attempted the install, where they advise you to remove a large bolt by having somone sit on the bike (or stand on its own against the wall) and have two (2) 18mm sockets on each side to remove the nut.

It was a PITA to remove by myself but it was done. After removing all the bolts and nuts that were supposed to be removed, they tell you to mount the bars to the bike. Everything till this point is fine. But then when trying to install that large bolt back into the bike, I can not do it.

The problem lies in the fact that the bars create a type of sleeve to go into the large hole that the bolt resides in to make it more sturdy. The sleeve, however, does not allow my 18mm socket to fit and so I can not tighten the bolt.

I have tried looking around for a socket that might fit but I can not find anything. Any suggestions? How did you do it? Is there something else I can do to tighten it down?

Here is a picture of the sleeve that is causing the problem. If more pictures are needed for context let me know.


tl;dr 18mm socket wont fit in the hole. What now?!
madpuma13 is offline   Reply With Quote
Old 01-21-2013, 06:25 PM   #2
lanceputnam
Hayden's Dad
 
lanceputnam's Avatar
 
Joined: Oct 2010
Location: Albuquerque, NM
Oddometer: 428
Go to napa or sears and get a " thin walled" 18 mm socket. They are specifically made for thing like this and for putting spark plugs into cylinder heads.
__________________
So others may live...

2012 BMW R1200 GS-Rallye
lanceputnam is offline   Reply With Quote
Old 01-22-2013, 04:42 PM   #3
madpuma13 OP
Gnarly Adventurer
 
Joined: Feb 2011
Location: CenTex
Oddometer: 109
Laugh

Yeah wow....
One of the sockets I tried was an 18mm spark plug socket.

I figured if a plug socket couldnt get in there (since I figured it would be thinwall) what would?! Turns out it isnt thinwall. Thanks for helping me
madpuma13 is offline   Reply With Quote
Old 01-22-2013, 10:35 PM   #4
Ayrshire Bull
why the hell not?
 
Ayrshire Bull's Avatar
 
Joined: Nov 2002
Location: The Left Coast, B.C., CA-NA-DA
Oddometer: 2,420
they're a bit tricky to go on - but worth the fight ...... keep at it Puma .....
__________________
"It's not what you look at that matters, it's what you see." - HDT
Ayrshire Bull is offline   Reply With Quote
Reply

Share

Thread Tools Search this Thread
Search this Thread:

.
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


Times are GMT -7.   It's 09:54 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ADVrider 2011-2014